BUREAU OF INDIAN STANDARDS
Programme of Work
PGD37 : General Engineering and Fasteners Standards
- Scope : a)Formulation of standards on (i)Basic mechanical engineering subjects for general applicability such as fasteners of all types (bolts, nuts, rivets, pins, nails, washers etc.), knurls, relief grooves, countersunks and counterbores, and (ii)Screw threads including basic profiles, pitch-diameter combination, terminology, technical requirement and tolerances but excluding screw thread gauges. b) Coordination of work with: (i) ISO/TC 1 Screw Thread (P-Member) (ii) ISO/TC 2 Fasteners (P-Member) (iii) ISO/TC 2/SC 7 Reference standard (P-Member) (iv) ISO/TC 2/SC 11 Fasteners with metric external thread (P-Member) (v) ISO/TC 2/SC 12 Fasteners with metric internal thread (P-Member) (vi) ISO/TC 2/SC 13 Fasteners with non-metric thread (P-Member) (vii) ISO/TC 2/SC 14 Surface coatings (O-Member)
-
Liaison :ISO/TC 1 - Screw threads - Participating (P)
ISO/TC 2 - Fasteners - Participating (P)
ISO/TC 2/SC 11 - Fasteners with metric external thread - Participating (P)
ISO/TC 2/SC 12 - Fasteners with metric internal thread - Participating (P)
ISO/TC 2/SC 13 - Fasteners with non-metric thread - Observer (O)
ISO/TC 2/SC 14 - Surface coatings - Participating (P)
ISO/TC 2/SC 7 - Reference standards - Participating (P)
|
IS 10102 : 1982 Reviewed In : 2021 |
Technical supply conditions for rivets
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 10238 : 2001 Reviewed In : 2021 |
Fasteners - Threaded steel fasteners - Step bolts for steel structures - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 10248 (Part 1) : 2011 Reviewed In : 2021 |
Parallel pins with internal thread: Part 1 unhardened steel and austenitic stainless steel (First Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 10248 (Part 2) : 2011 Reviewed In : 2021 |
Parallel pins with internal thread: Part 2 hardened steel and martensitic stainless steel (First Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 10587 : 1983 Reviewed In : 2021 |
Terminology for screw threads
|
February, 2021
|
-
|
Indigenous
|
|
|
IS/ISO 10683 : 2018 ISO 10683 : 2018 |
Fasteners - Non-Electrolytically Applied Zinc Flake Coating Systems
|
-
|
Identical under single numbering
|
||
|
IS 1120 : 1975 Reviewed In : 2021 |
Specification for coach screws (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 11362 : 1985 ISO 7721 Reviewed In : 2021 |
Head configuration and gauging of countersunk head screws
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 12186 : 1987 Reviewed In : 2019 |
Tolerances for ISO - vietric trapezoidal screw threads for lead and feed screw assemblies
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 12427 : 2001 Reviewed In : 2021 |
Fasteners - Threaded steel fasteners - Hexagon head transmission tower bolts - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 12952 : 2005 ISO 8740 Reviewed In : 2021 |
Grooved pins - Full - Length parallel grooved, with chamfer (First Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 12982 : 1991 ISO 8749 Reviewed In : 2021 |
Pins and grooved pins - Shear test
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 1363 (Part 1) : 2023 ISO 4016 : 2022 |
Hexagon head bolts, screws and nuts of product grade C Part 1 Hexagon head bolts (Size range M5 to M64) (sixth revision)
|
-
|
Identical under dual numbering
|
||
|
IS 1363 (Part 2) : 2023 ISO 4018 : 2022 |
Hexagon head bolts, screws and nuts of product grade C Part 2 Hexagon head screws (Size range M5 to M64) (sixth revision)
|
-
|
Identical under dual numbering
|
||
|
IS 1363 (Part 3) : 2018 ISO 4034 Reviewed In : 2024 |
Hexagon Head Bolts, Screws and Nuts of Product Grade ‘C’ Part 3 (Style 1) Hexagon Nuts ( Size Range M 5 to M 64 ) ( Fifth Revision )
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1364 (Part 1) : 2023 ISO 4014 : 2022 |
Hexagon head bolts, screws, and nuts of property grades A and B: Part 1 Hexagon head bolts (Size range M1.6 to M64) (sixth revision)
|
-
|
Identical under dual numbering
|
||
|
IS 1364 (Part 2) : 2023 ISO 4017 : 2022 |
Hexagon head bolts screws and nuts of product grades A and B Part 2 Hexagon head screws (Size range M1.6 to M64 ) (Sixth revision of IS 1364 (Part 2))
|
-
|
Identical under dual numbering
|
||
|
IS 1364 (Part 2) : 2018 ISO 4017 Reviewed In : 2018 |
Hexagon head bolts, screws and nuts of product grades A and B: Part 2 hexagon head screws (Size Range M 1.6 To M 64) (Fifth Revision)
|
-
|
-
|
Identical under dual numbering
|
|
|
IS 1364 (Part 3) : 2018 Reviewed In : 2023 |
Hexagon Head Bolts, Screws and Nuts of Product Grades A and B Part 3 Hexagon Nuts, Style 1 ( Size Range M 1.6 To M 64 )
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1364 (Part 4) : 2003 ISO 4035 Reviewed In : 2023 |
Hexagon head bolts, screws and nuts of product grades A and B: Part 4 hexagon thin nuts (Chamfered) (Size Range M1.6t0 M64) (Fourth Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1364 (Part 5) : 2002 ISO 4036 Reviewed In : 2023 |
Hexagon head bolts, screws and nuts of product grades A and B: Part 5 hexagon thin nuts - Product grade B (Unchamfered) (Size Range M 1.6t0 M 10) (Fourth Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1364 (Part 6) : 2018 ISO 4033 : 2012 Reviewed In : 2023 |
Hexagon Head Bolts, Screws and Nuts of Product Grades A and B Part 6 Hexagon Nuts, Style 2 ( First Revision )
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1365 : 2022 ISO 2009 : 2011 |
Slotted countersunk flat head screws Product grade A Fifth Revision of IS 1365
|
-
|
Identical under dual numbering
|
||
|
IS 1366 : 2022 ISO 1207 : 2011 |
Slotted Cheese Head Screws � Product Grade A (Fourth Revision of IS 1366)
|
-
|
Identical under dual numbering
|
||
|
IS 1367 (Part 1) : 2014 ISO 8992 : 2005 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners: Part 1 general requirements for bolts, screws, studs and nuts (Fourth Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 2) : 2002 ISO 4759-1 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners: Part 2 tolerances for fasteners - Bolts, screws, studs and nuts - Product grades a, b and c (Third Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 3) : 2017 ISO 898-1 : 2013 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)
|
September, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 5) : 2018 ISO 898-5 : 2012 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners: Part 5 mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (Fourth Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 6) : 2018 ISO 898-2 : 2012 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 7) : 1980 Reviewed In : 2023 |
Technical supply conditions for tHreadeD steel fasteners: Part 7 mechanical properties and test methods for nuts without specified proof loads (Second Revision)
|
April, 2023
|
1
|
Modified/Technically Equivalent
|
|
|
IS 1367 (Part 8) : 2020 ISO 2320 : 2015 Reviewed In : 2024 |
Technical Supply Conditions for Threaded Steel Fasteners Part 8 Prevailing Torque Type Steel Nuts — Functional Properties ( Fifth Revision )
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 9/Sec 1) : 1993 ISO 6157-1 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners: Part 9 surface discontinuities section 1 bolts, screws and studs for general applications (Third Revision)
|
April, 2024
|
1
|
Identical under dual numbering
|
|
|
IS 1367 (Part 9/Sec 2) : 1993 ISO 6157-3 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners: Part 9 surface discontinuities section 2 bolts, screws and studs for special applications (Third Revision)
|
April, 2024
|
1
|
Identical under dual numbering
|
|
|
IS 1367 (Part 10) : 2002 ISO 6157-2 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners: Part 10 surface discontinuities - Nuts (Third Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 11) : 2020 |
Technical Supply Conditions for Threaded Steel Fasteners Part 11 Electroplated Coating Systems ( Fourth Revision )
|
-
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 12) : 1981 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners: Part 12 phosphate coatings on threaded fasteners (Second Revision)
|
April, 2024
|
-
|
Modified/Technically Equivalent
|
|
|
IS 1367 (Part 13) : 2020 ISO 10684 : 2004 Reviewed In : 2024 |
Technical Supply Conditions for Threaded Steel Fasteners Part 13 Hot Dip Galvanized Coatings on Threaded Fasteners ( Third Revision )
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 14/Sec 1) : 2023 ISO 3506-1 : 2020 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless Steel Fasteners Section 1 Bolts screws and studs with specified grades and property classes (Fifth Revision of IS 1367(Part 14 Sec 1))
|
-
|
Identical under dual numbering
|
||
|
IS 1367 (Part 14/Sec 2) : 2023 ISO 3506-2 : 2020 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless steel Fasteners Section 2 Nuts with specified grades and property classes
|
-
|
Identical under dual numbering
|
||
|
IS 1367 (Part 14/Sec 3) : 2018 ISO 3506-3 : 2009 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners: Part 14 mechanical properties of corrosion - Resistant stainless steel fasteners section 3 set screws and similar fasteners not under tensile stress (Fourth Revision
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 14/Sec 4) : 2023 ISO 3506-4 : 2009 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion Resistant Stainless Steel Fasteners Section 4 Tapping Screws
|
-
|
Identical under dual numbering
|
||
|
IS 1367 (Part 16) : 2002 ISO 8991 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners: Part 16 designation system for fasteners (Third Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 17) : 2023 ISO 3269 : 2019 |
Technical Supply Conditions for Threaded Steel Fasteners Part 17 Inspections Sampling and Acceptance Procedure Fifth Revision of IS 1367 Part 17
|
-
|
Identical under dual numbering
|
||
|
IS 1367 (Part 18) : 1996 Reviewed In : 2021 |
Industrial fasteners - Threaded steel fasteners - Technical supply conditions: Part 18 packaging (Third Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 1367 (Part 19) : 1997 ISO 3800 Reviewed In : 2024 |
Industrial fasteners - Threaded steel fasteners - Technical supply conditions: Part 19 axial load fatigue testing of bolts, screws and studs
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1367 (Part 20) : 1996 ISO 898-7 Reviewed In : 2021 |
Industrial fasteners - Threaded steel fasteners - Technical supply conditions - Mechanical properties: Part 20 torsional - Test and mlnimum torques for bolts and screws with nominal diameters 1 mm to 10 mm
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 1368 : 2018 ISO 4753 : 2011 Reviewed In : 2023 |
Dimensions for ends of parts with external ISO metric threads (Fourth Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 1369 (Part 1) : 1993 ISO 3508 Reviewed In : 2024 |
Fasteners - Thread run - Outs and under - cuts: Part 1 dimensions for screw thread run - Outs for external ISO metric threads (Third Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1369 (Part 2) : 1993 ISO 4755 Reviewed In : 2024 |
Fasteners - Thread run - Outs and undercuts: Part 2 dimensions for screw thread undercuts for external ISO metric threads (Third Revision ;
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 1369 (Part 3) : 2021 |
Fasteners - Thread Run-Outs and Undercuts - Part 3 : Dimensions for Screw Thread Run-Outs and Undercuts for Internal Threads Blind Tapped Holes Third Revision
|
-
|
Indigenous
|
||
|
IS 13722 : 2002 ISO 8673 : 2012 Reviewed In : 2023 |
Hexagon regular nuts (Style 1) with metric fine pitch thread - Product grades A and B (Second Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 13723 : 2018 ISO 8674 : 2012 Reviewed In : 2024 |
Hexagon High Nuts (Style 2) With Metric Fine Pitch Thread - Product Grades A and B (Second Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 13724 : 2018 ISO 8675 : 2012 Reviewed In : 2024 |
Hexagon thin nuts chamfered (Style 0) with metric fine pitch thread - Product grades A and B (Second Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 13725 : 2023 ISO 8676 : 2022 |
Hexagon Head Screws With Metric Fine Pitch Thread Product Grades A and B Third Revision of 13275
|
-
|
Identical under dual numbering
|
||
|
IS 13726 : 2023 ISO 8765 : 2022 |
Hexagon head bolts with metric fine pitch thread � Product grades A and B (third revision)
|
-
|
Identical under dual numbering
|
||
|
IS 14394 : 1996 Reviewed In : 2021 |
Industrial fasteners - Hexagon nuts of product grade C - Hot - Dip galvanized - Specification (Size Range M12 To M36)
|
February, 2021
|
-
|
Not Equivalent
|
|
|
IS 14894 : 2023 ISO/FDIS 4015 : 2021 |
Fasteners � Hexagon head bolts of product grade B � Reduced shank (shank diameter ? pitch diameter) � Specification
|
-
|
Identical under dual numbering
|
||
|
IS 14962 (Part 1) : 2018 ISO 965-1 : 2013 Reviewed In : 2023 |
ISO general purpose metric screw threads - Tolerances: Part 1 principles and basic data (First Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 14962 (Part 2) : 2001 ISO 965 : Part 2 Reviewed In : 2023 |
ISO general purpose metric screw threads - Tolerances: Part 2 limits of sizes for general purpose external and internal screw threads - Medium quality
|
April, 2023
|
1
|
Identical under dual numbering
|
|
|
IS 14962 (Part 3) : 2022 ISO 965-3: 2021 |
ISO general purpose metric screw threads � Tolerances � Part 3: Limit deviations for screw threads
|
-
|
Identical under dual numbering
|
||
|
IS 14962 (Part 4) : 2023 ISO 965-4 : 2021 |
ISO General purpose metric screw threads - Tolerances Part 4 Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing (First revision of IS 14962( Part 4 ) )
|
-
|
Identical under dual numbering
|
||
|
IS 14962 (Part 5) : 2001 ISO 965 : Part 5 Reviewed In : 2023 |
ISO general purpose metric screw threads - Tolerances: Part 5 limits of sizes for internal screw threads to mate with hot - Dip galvanized external screw threads with maximum size of tolerance position H before galvanizing
|
April, 2023
|
1
|
Identical under dual numbering
|
|
|
IS/ISO 1501 : 2009 ISO 1501 : 2009 Reviewed In : 2024 |
ISO miniature screw threads
|
April, 2024
|
1
|
Identical under single numbering
|
|
|
IS 15274 : 2021 ISO 4759-3:2016 |
Tolerances for fasteners Washers for bolts screws and nuts Product grades A C and F First Revision of IS 15274 ISO 4759-3 : 2016 ICS 2106030
|
-
|
Identical under dual numbering
|
||
|
IS 15568 : 2005 ISO 10485 Reviewed In : 2021 |
Cone proof load test on nuts
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 15569 : 2005 ISO 10484 Reviewed In : 2021 |
Widening test on nuts
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 15581 : 2018 ISO 4161 : 2012 Reviewed In : 2023 |
Hexagon nuts with flange, style 2 - Coarse thread (First Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 15582 : 2018 ISO 4162 : 2012 Reviewed In : 2023 |
Hexagon Bolts with Flange - Small Series - Product Grade A with Driving Feature of Product Grade B ( First Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 15628 : 2022 ISO 4766 : 2011 |
Slotted set screws with flat point - Specification First Revision of IS 15628 ICS 2106010
|
-
|
Identical under dual numbering
|
||
|
IS 15629 : 2005 ISO 7434 Reviewed In : 2021 |
Slotted set screws with cone point
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 15630 : 2005 ISO 7435 Reviewed In : 2021 |
Slotted set screws with long dog point
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 15631 : 2005 ISO 7436 Reviewed In : 2021 |
Slotted set screws with cup point
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 15705 : 2006 ISO 23429 Reviewed In : 2024 |
Gauging of hexagon sockets
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS/ISO 16426 : 2002 ISO 16426 : 2002 Reviewed In : 2021 |
Fasteners - Quality assurance system
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 17445 : 2020 ISO 15330 : 1999 Reviewed In : 2024 |
Fasteners — Preloading Test for the Detection of Hydrogen Embrittlement — Parallel Bearing Surface Method
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 17894 : 2022 ISO 22081 : 2021 |
Geometrical product specifications GPS - Geometrical tolerancing - General geometrical specifications and general size specifications
|
-
|
Identical under dual numbering
|
||
|
IS 1821 : 1987 ISO 273 Reviewed In : 2024 |
Dimensions for clearance holes for bolts and screws (Third Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 18471 (Part 1) : 2023 ISO 15481:1999 |
Fasteners � Cross Recessed Drilling Screws with Tapping Screw Thread Part 1 Pan Head
|
-
|
Identical under dual numbering
|
||
|
IS 18471 (Part 2) : 2023 ISO 15482:1999 |
Fasteners � Cross Recessed Drilling Screws with Tapping Screw Thread Part 2 Countersunk Head
|
-
|
Identical under dual numbering
|
||
|
IS 18471 (Part 3) : 2023 ISO 15483:1999 |
Fasteners � Cross Recessed Drilling Screws with Tapping Screw Thread Part 3 Raised Countersunk Head
|
-
|
Identical under dual numbering
|
||
|
IS 18476 : 2023 ISO 15480:2019 |
Fasteners � Hexagon Washer Head Drilling Screws with Tapping Screw Thread
|
-
|
Identical under dual numbering
|
||
|
IS 18480 (Part 1) : 2023 ISO 7049 : 2011 |
Cross Recessed Tapping Screws: Part 1 Pan Head
|
-
|
Identical under dual numbering
|
||
|
IS 18480 (Part 2) : 2023 ISO 7050 : 2011 |
Cross Recessed Tapping Screws Part 2 Countersunk Flat Head
|
-
|
Identical under dual numbering
|
||
|
IS 18480 (Part 3) : 2023 ISO 7051 : 2011 |
Cross Recessed Tapping Screw Part 3 Raised Countersunk Oval Head
|
-
|
Identical under dual numbering
|
||
|
IS 18507 : 2024 |
Drywall Screws � Specification
|
-
|
Indigenous
|
||
|
IS 18508 : 2024 |
Chipboard Screws � Specification
|
-
|
Indigenous
|
||
|
IS 18509 : 2024 |
Cross-recessed Countersunk Head Wood Screws � Specification
|
-
|
Indigenous
|
||
|
IS 1862 : 1975 Reviewed In : 2021 |
Specification for studs (Second Revision)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 18741 : 2024 |
Concrete Nails � Specification
|
-
|
Indigenous
|
||
|
IS 1928 : 1961 Reviewed In : 2021 |
Specification for boiler rivets (12 To 48 Mm Diameter)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 1929 : 1982 Reviewed In : 2021 |
Specification for hot forged steel rivets for hot closing (12 To 36 Mm Diameter)
|
February, 2021
|
4
|
Indigenous
|
|
|
IS 2016 : 1967 Reviewed In : 2021 |
Specification for plain washers (First Revision)
|
February, 2021
|
4
|
Indigenous
|
|
|
IS 207 : 1964 Reviewed In : 2021 |
Specification for gate and shutter hooks and eyes (Revised)
|
February, 2021
|
2
|
Indigenous
|
|
|
IS 2102 (Part 1) : 1993 ISO 2768-1-89 Reviewed In : 2024 |
General tolerances: Part 1 tolerances for linear and angular dimensions without individual tolerance indications (Third Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 2155 : 1982 Reviewed In : 2021 |
Specification for cold forged solid steel rivets for hot closing (6 To 16 Mm Diameter) (First Revision)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 2186 : 1985 Reviewed In : 2021 |
ISO metric external screw threads for interference fit applications (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 2232 : 1967 Reviewed In : 2021 |
Specification for slotted and castle nuts (First Revision)
|
February, 2021
|
3
|
Indigenous
|
|
|
IS 2269 : 2006 ISO 4762 Reviewed In : 2021 |
Hexagon socket head cap screws (Fifth Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 2393 : 2010 Reviewed In : 2021 |
Parallel pins, of unhardened steel and austenitic stainless steel (Third Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 2473 : 1975 Reviewed In : 2024 |
Dimensions for centre holes (First Revision)
|
September, 2024
|
2
|
Indigenous
|
|
|
IS 2540 : 2008 Reviewed In : 2019 |
Dimensions for threaded centre holes (First Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 2585 : 2006 Reviewed In : 2021 |
Square head bolts, screws and square nuts of product grade C - Specification (Second Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 2609 : 1972 Reviewed In : 2024 |
Specification for coach bolts (First Revision)
|
April, 2024
|
3
|
Indigenous
|
|
|
IS 2636 : 1972 Reviewed In : 2021 |
Specification for wing nuts (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 2638 : 1974 Reviewed In : 2021 |
Specification for flat split cotters (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 2643 : 2005 Reviewed In : 2021 |
Pipe threads where pressure - Tight joints are not made on the threads - Dimensions, tolerances and designation (Third Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 2687 : 1991 Reviewed In : 2021 |
Capnuts - Specification (Second Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 2769 : 1969 Reviewed In : 2024 |
Sizes for squares and square holes for general engineering purposes (First Revision
|
September, 2024
|
-
|
Indigenous
|
|
|
IS 2907 : 1998 Reviewed In : 2019 |
Non - Ferrous rivets - Specification (First Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 2998 : 1982 Reviewed In : 2019 |
Specification for cold forged steel rivets for cold closing (1 To 16 mm Diameter) (First Revision)
|
December, 2019
|
3
|
Indigenous
|
|
|
IS 3063 : 1994 Reviewed In : 2021 |
Fasteners - Single coil rectangular section spring lock washers specification (Second Revision)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 3403 : 1981 Reviewed In : 2024 |
Dimensions for knurls (First Revision)
|
September, 2024
|
-
|
Indigenous
|
|
|
IS 3406 (Part 1) : 1986 Reviewed In : 2024 |
Dimensions for countersinks and counterbores: Part 1 countersinks (Second Revision)
|
September, 2024
|
-
|
Indigenous
|
|
|
IS 3406 (Part 2) : 2014 Reviewed In : 2019 |
Dimensions for countersinks and counterbores: Part 2 counterbores (Third Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 3428 : 2009 Reviewed In : 2019 |
Dimensions for relief grooves (Second Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 3457 : 2009 Reviewed In : 2024 |
Radii for rounding for general engineering purposes (Second Revision)
|
April, 2024
|
-
|
Indigenous
|
|
|
IS 3458 : 2018 ISO 1119 : 2011 Reviewed In : 2023 |
Conical tapers and taper angles for general engineering purposes (Third Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 3460 : 1991 Reviewed In : 2021 |
Knurled nuts - Specification (Second Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 3468 : 1991 Reviewed In : 2021 |
Pipe nuts - Specification (Second Revision)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 3524 (Part 1) : 1982 Reviewed In : 2021 |
Specification for threaded taper pins: Part 1 with internal threads (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 3524 (Part 2) : 1982 Reviewed In : 2021 |
Specification for threaded taper pins: Part 2 with external threads (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 3640 : 1982 Reviewed In : 2021 |
Specification for hexagon fit bolts (First Revision)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 3726 : 2003 Reviewed In : 2024 |
Thumb screws - Specification (Second Revision)
|
April, 2024
|
-
|
Indigenous
|
|
|
IS 3727 : 1966 Reviewed In : 2021 |
Specification for wing screws
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 3757 : 1985 Reviewed In : 2019 |
Specification for high strength structural bolts (Second Revision)
|
December, 2019
|
2
|
Indigenous
|
|
|
IS 3974 : 1967 Reviewed In : 2021 |
Specification for bifurcated rivets for general purposes
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4040 : 1998 Reviewed In : 2024 |
Fasteners - Solid drilled tubular and semi - Tubular rivets - Specification (First Revision)
|
April, 2024
|
2
|
Indigenous
|
|
|
IS 4172 : 2005 ISO 885 Reviewed In : 2021 |
General purpose bolts and screws - Metric series - Radii under the head (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
SP 42 : 2008 Reviewed In : 2021 |
Survey of screw threads (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4206 : 2012 ISO 888 : 2012 Reviewed In : 2024 |
Dimensions for nominal lengths and thread lengths for bolts, screws and studs (Second Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 4218 (Part 1) : 2001 ISO 68-1 Reviewed In : 2023 |
ISO general purpose metric screw threads: Part 1 basic profile - second revision)
|
April, 2023
|
1
|
Identical under dual numbering
|
|
|
IS 4218 (Part 2) : 2001 ISO 261 Reviewed In : 2023 |
ISO general purpose metric screw threads: Part 2 general plan (Second Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 4218 (Part 3) : 1999 ISO 724 Reviewed In : 2021 |
ISO general purpose metric screw threads: Part 3 basic dimensions (Second Revision)
|
February, 2021
|
1
|
Identical under dual numbering
|
|
|
IS 4218 (Part 4) : 2001 Reviewed In : 2023 |
ISO general purpose metric screw threads: Part 4 selected sizes for screws, bolts and nuts (Second Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 4499 : 1968 Reviewed In : 2021 |
Dimensions for depth of holes for studs
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 451 : 1999 Reviewed In : 2021 |
Technical supply conditions for wood screws (Third Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4695 (Part 1) : 2003 Reviewed In : 2021 |
General purpose knuckle threads: Part 1 profile and nominal sizes (Second Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4695 (Part 2) : 2003 Reviewed In : 2021 |
General purpose knuckle threads: Part 2 deviations and tolerances (Second Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4696 (Part 1) : 2004 Reviewed In : 2019 |
DIMENSIONS FOR METRIC BUTTRESS THREADS PART 1 THREAD PROFILES (Second Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 4696 (Part 2) : 2004 Reviewed In : 2019 |
DIMENSIONS FOR METRIC BUTTRESS THREADS PART 2 PITCH DIAMETER COMBINATIONS (Second Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 4696 (Part 3) : 2004 Reviewed In : 2019 |
Dimensions for metric buttress threads: Part 3 basic dimensions (Second Revision)
|
December, 2019
|
-
|
Indigenous
|
|
|
IS 4696 (Part 4) : 2005 Reviewed In : 2021 |
Dimensions for metric buttress threads: Part 4 tolerancing system (Second Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4732 : 1968 Reviewed In : 2021 |
Specification for rivets for shipbuilding
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 4762 : 2002 Reviewed In : 2021 |
FASTENERS — WORM DRIVE HOSE CLAMPS FOR GENERAL PURPOSES — SPECIFICATION ( Second Revision )
|
February, 2021
|
4
|
Indigenous
|
|
|
IS 5368 : 1969 Reviewed In : 2021 |
Specification for thin slotted and castle nuts (Dia Range 6 To 52 Mm)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 5370 : 1969 Reviewed In : 2021 |
Specification for plain washers with outside diameter 3 x inside diameter
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 5371 : 1982 Reviewed In : 2021 |
Specification for multi - Tooth lock washers (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 5372 : 1975 Reviewed In : 2021 |
Specification for taper washers for channels (ISMC) (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 5373 : 1969 Reviewed In : 2021 |
Specification for square washers for wood fastenings
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 5374 : 1975 Reviewed In : 2021 |
Specification for taper washers for I - Beams (Ismb) (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS/ISO 5408 : 2009 ISO 5408 : 2009 Reviewed In : 2024 |
Screw threads - Vocabulary
|
April, 2024
|
-
|
Identical under single numbering
|
|
|
IS 549 : 2005 Reviewed In : 2021 |
Split pins - Specification (Third Revision)
|
February, 2021
|
4
|
Identical under dual numbering
|
|
|
IS 554 : 1999 ISO 7-1 Reviewed In : 2024 |
Pipe threads where pressure - Tight joints are made on the threads - Dimensions, tolerances and designation (Fourth Revision)
|
April, 2024
|
1
|
Identical under dual numbering
|
|
|
IS 5554 : 1991 Reviewed In : 2021 |
Lock washers with lug - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 5556 : 1991 Reviewed In : 2021 |
Serratedlockwashers - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 5624 : 2021 |
FOUNDATION BOLTS SPECIFICATION Second Revision
|
-
|
Modified/Technically Equivalent
|
||
|
IS 5957 : 2003 ISO 1478-1999 Reviewed In : 2023 |
Screw threads for thread forming tapping screws dimensions (Second Revision)
|
April, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 6094 (Part 1) : 2006 ISO 4026 Reviewed In : 2024 |
Hexagon socket set screws: Part 1 with flat point (Third Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 6094 (Part 2) : 2006 ISO 4027 Reviewed In : 2021 |
Hexagon socket set screws: Part 2 with cone point (Third Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 6094 (Part 3) : 2006 ISO 4028 Reviewed In : 2021 |
Hexagon socket set screws: Part 3 with dog point (Third Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 6094 (Part 4) : 2006 ISO 4029 Reviewed In : 2021 |
Hexagon socket set screws: Part 4 with cup point (Third Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 6101 : 2018 ISO 1580 : 2011 Reviewed In : 2023 |
Slotted pan head screws - Product grade a (Third Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 6113 : 1970 Reviewed In : 2021 |
Specification for aluminium fasteners for buildin - g purposes
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 6610 : 1972 Reviewed In : 2021 |
Specification for heavy washers for steel structures
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 6623 : 2004 Reviewed In : 2021 |
High Strength Structural Nuts
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 6639 : 1972 Reviewed In : 2021 |
Specification for hexagon bolts for steel structures
|
February, 2021
|
5
|
Indigenous
|
|
|
IS 6649 : 1985 Reviewed In : 2021 |
Specification for hardened and tempered washers for high strength structural bolts and nuts (First Revision)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 6688 : 2005 Reviewed In : 2021 |
Taper pins, unhardened (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 6689 : 2003 ISO 8734 Reviewed In : 2024 |
Parallel pins of hardened steel and martensitic stainless steel (Dowel Pins) (First Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 6730 : 1972 Reviewed In : 2021 |
Specification for felt nails
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 6732 : 1972 Reviewed In : 2021 |
Specification for double point nails
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 6733 : 1972 Reviewed In : 2021 |
Specification for wall and roofing nails
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 6734 : 1972 Reviewed In : 2021 |
Specification for cut lath and lath nails
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 6735 : 1994 Reviewed In : 2019 |
Fasteners - Spring lock wasixers for screws with cylindrical heads - Specification (First Revision)
|
December, 2019
|
1
|
Indigenous
|
|
|
IS 6736 : 1972 Reviewed In : 2021 |
Specification for slotted raised countersunk head wood screws
|
February, 2021
|
2
|
Indigenous
|
|
|
IS 6738 : 1972 Reviewed In : 2021 |
Specification for panel pins and lost head nails
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 6739 : 1972 Reviewed In : 2021 |
Slotted Round Head Wood Screws
|
February, 2021
|
2
|
Indigenous
|
|
|
IS 6755 : 1980 Reviewed In : 2021 |
Specification for double coil helical spring washers (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 6760 : 1972 Reviewed In : 2021 |
Specification for slotted countersunk head wood screws
|
February, 2021
|
2
|
Indigenous
|
|
|
IS 6761 : 2023 ISO 10642 : 2019 |
Fasteners Hexagon Socket Countersunk Head Screws with Reduced Loadability Third Revision of IS 6761
|
-
|
Identical under dual numbering
|
||
|
IS 6821 : 1973 Reviewed In : 2021 |
Methods for sampllNg non - Threaded fasteners
|
February, 2021
|
2
|
Indigenous
|
|
|
IS 6862 : 2005 Reviewed In : 2021 |
Clews pins without head (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 6863 : 2005 Reviewed In : 2021 |
Clevis pins with head (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7002 : 2018 ISO 7040 : 2012 Reviewed In : 2023 |
Prevailing torque type hexagon regular nuts (With Non - Metallic Insert) - Property classes 5, 8 and 10 (Third Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7008 (Part 1) : 2021 ISO 2901 : 2016 |
ISO metric trapezoidal screw threads Part 1 Basic and design profile Third Revision IS 7008 Part 1 ISO 2901 : 2016 ICS 2106010
|
-
|
Identical under dual numbering
|
||
|
IS 7008 (Part 2) : 2021 ISO 2902 : 2016 |
ISO metric trapezoidal screw threads Part 2 General plan Second Revision IS 7008 Part 2 ISO 2902 : 2016 ICS 2106010
|
-
|
Identical under dual numbering
|
||
|
IS 7008 (Part 3) : 2023 ISO 2904 : 2020 |
ISO METRIC TRAPEZOIDAL SCREW THREADS PART 3 BASIC DIMENSIONS (Second Revision of IS 7008(Part 3))
|
-
|
Identical under dual numbering
|
||
|
IS 7008 (Part 4) : 2021 ISO 2903 : 2016 |
ISO metric trapezoidal screw threads Part 4 Tolerances Third Revision IS 7008 Part 4 ISO 2903 : 2016 ICS 2106010
|
-
|
Identical under dual numbering
|
||
|
IS 7169 : 2018 ISO 1483-2011 Reviewed In : 2023 |
Slotted raised countersunk (Oval) head tapping screws (Second Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7170 : 2018 ISO 1482-2011 Reviewed In : 2023 |
Slotted countersunk (Flat) head tapping screws (Second Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7173 : 2018 ISO 1481-2011 Reviewed In : 2023 |
Slotted pan head tapping screws (Second Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7178 : 2018 ISO 2702 : 2011 Reviewed In : 2024 |
Heat - Treated steel tapping screws - Mechanical properties (Fourth Revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 723 : 1972 Reviewed In : 2021 |
Specification for steel countersunk head wire nails (First Revision)
|
February, 2021
|
3
|
Indigenous
|
|
|
IS 723 : 2023 |
Steel Countersunk Head Wire Nails � Specification ( Second Revision )
|
-
|
Indigenous
|
||
|
IS 724 : 2023 |
Mild Steel and Brass Cup, Ruler and Square Hooks and Screw Eyes � Specification
|
-
|
Indigenous
|
||
|
IS 725 : 1961 Reviewed In : 2021 |
Specification for copper wire nails (Revised)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 730 : 2021 |
Specification for Hook Bolts for Corrugated Sheet Roofing
|
-
|
Indigenous
|
||
|
IS 7368 : 2005 ISO 8744 Reviewed In : 2021 |
Grooved pins - Full - Length taper grooved (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7383 : 2005 ISO 8742 Reviewed In : 2021 |
Grooved puns - One - Third - Length centre grooved (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7384 : 2005 ISO 8739 Reviewed In : 2021 |
Grooved pins - Full - Length parallel grooved, with pilot (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7385 : 2005 ISO 8745 Reviewed In : 2021 |
Grooved pins - Half - Length taper grooved (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7386 : 2005 ISO 8741 Reviewed In : 2021 |
Grooved pins - Half - Length reverse taper grooved (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7478 : 2011 ISO 4757:1983 Reviewed In : 2021 |
Cross recesses for screws (Second Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 7483 : 2018 Reviewed In : 2023 |
Pan Head Screws With Type H or Type Z Cross Recess - Product Grade A (Third Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7485 (Part 1) : 2018 ISO 7046-1 : 2011 Reviewed In : 2023 |
Countersunk Flat Head Screws (Common head Style) With Type H or Type Z Cross Recess - Product Grade A Part 1 Steel Screws of Property Class 4.8 ( Third Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7485 (Part 2) : 2018 ISO 7046-2 : 2011 Reviewed In : 2023 |
Countersunk flat head screws (common head style) with type H or Type Z Cross Recess - Product Grade A part 2 Steel Screws of Property Class 8.8, Stainless Steel Screws and Non - Ferrous Metal Screws ( Third Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7486 : 2018 ISO 7047 : 2011 Reviewed In : 2023 |
Raised countersunk head screws (Common Head Style) with type H or type Z cross recess - Product grade A (Third Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 7519 : 1974 Reviewed In : 2021 |
Specification for hammer drive screws
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 7615 : 2003 Reviewed In : 2024 |
System of cone tolerance for conical workpiece from c = 1:3 to 1:500 and lengths from 6 to 630 mm (Second Revision)
|
April, 2024
|
-
|
Indigenous
|
|
|
IS 7684 : 1975 Reviewed In : 2021 |
LIMITS OF SIZES FOR ISO METRIC TRAPEZOIDAL NUT THREADS DIAMETER RANGE 8 TO 100 mm
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 7685 : 1975 Reviewed In : 2021 |
Limits of sizes for ISO metric trapezoidal bolt threads (Diameter Range 8 To 100 Mm)
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 7726 : 1975 Reviewed In : 2024 |
Limits of sizes for ISO metric trapezoidal nut threads (Diameter Range 105 To 300 Mm)
|
September, 2024
|
1
|
Indigenous
|
|
|
IS 7727 : 1975 Reviewed In : 2024 |
Limits of sizes for ISO metric trapezoidal bolt threads (Diameter Range 105 To 300 Mm)
|
September, 2024
|
1
|
Indigenous
|
|
|
IS 7790 : 1991 Reviewed In : 2021 |
Domed cap nuts - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 7795 : 2004 Reviewed In : 2021 |
Hexagon nuts with collar - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 7800 : 1990 Reviewed In : 2021 |
Thread cutting tapping screwsscrew threads and ends - Dimensions (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8033 : 1976 Reviewed In : 2021 |
Specification for round washers with square hole for wood fastenings
|
February, 2021
|
2
|
Indigenous
|
|
|
IS 8068 : 1976 Reviewed In : 2021 |
Specification for tab washers
|
February, 2021
|
1
|
Indigenous
|
|
|
IS 8070 : 1991 Reviewed In : 2021 |
Screws - Slotted capstan (Tommy bolts) - Specification (First Revision)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8217 : 1976 Reviewed In : 2021 |
Dimensions of pipe thread runouts and undercuts
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8351 : 1977 Reviewed In : 2021 |
Specification for spiral pins (Heavy Duty Type)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8352 : 1977 Reviewed In : 2021 |
Specification for flat countersunk square neck bolts
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8353 : 1977 Reviewed In : 2021 |
Specification for flat countersunk nib bolts
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8379 : 1977 Reviewed In : 2021 |
Specification for spiral pins (Medium - Duty Type)
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8412 : 1977 Reviewed In : 2021 |
Specification for slotted countersunk head bolts for steel structures
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8535 : 2020 ISO 1891 : 2009 Reviewed In : 2024 |
Fasteners — Terminology ( Second Revision )
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 8536 : 2021 ISO 225 : 2010 |
Fasteners - Bolts screws studs and nuts - Symbols and designation of dimensions First Revision IS 8536
|
-
|
Identical under dual numbering
|
||
|
IS 866 : 1957 Reviewed In : 2021 |
Specification forTinmens Rivets
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8721 : 1978 Reviewed In : 2021 |
Specification for fish bolts (Cup Oval Neck Bolts) for collieries
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8722 : 1978 Reviewed In : 2021 |
Specification for fish bolts with square head
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8788 : 2002 Reviewed In : 2024 |
Dimensions for metric external taper and internal parallel screw threads september 2002 (Second Revision)
|
September, 2024
|
-
|
Indigenous
|
|
|
IS 8822 : 1978 Reviewed In : 2021 |
Specification for slotted mushroom head roofing bolts
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8841 : 1978 Reviewed In : 2024 |
Recommendations for limits and flTs for sizes above 3 i50 mm up to io 000 mm
|
April, 2024
|
-
|
Indigenous
|
|
|
IS 8856 : 1991 Reviewed In : 2019 |
Hexagon weld nuts - Specification (First Revision)
|
December, 2019
|
1
|
Indigenous
|
|
|
IS 8869 : 1978 Reviewed In : 2021 |
Specification for washers for corrugated sheet roofing
|
February, 2021
|
-
|
Indigenous
|
|
|
IS 8911 : 2018 ISO 2010 : 2011 Reviewed In : 2023 |
Slotted raised countersunk head screws - Product grade A (Second Revision)
|
October, 2023
|
-
|
Identical under dual numbering
|
|
|
IS 919 (Part 1) : 2014 ISO 286-1 : 2010 Reviewed In : 2024 |
Geometrical Product Specifications (GPS) - ISO Code System for Tolerances on Linear Sizes Part 1 Basis of Tolerance, Deviation and Fits (Third Revision)
|
April, 2024
|
1
|
Identical under dual numbering
|
|
|
IS 919 (Part 2) : 2014 ISO 286-2 Reviewed In : 2024 |
Geometrical product specifications (GPS) - ISO code system for tolerances on linear sizes: Part 2 tables of standard tolerance classes and limit deviation for holes and shafts (Second Revision)
|
April, 2024
|
1
|
Identical under dual numbering
|
|
|
IS 9519 : 2005 Reviewed In : 2021 |
Fasteners - Hexagon products - Width across flats (First Revision)
|
February, 2021
|
-
|
Identical under dual numbering
|
|
|
IS 9549 (Part 1) : 2014 ISO 7378:1983 Reviewed In : 2024 |
Fasteners -- Bolts, screws and studs: Part 1 Split pin holes and wire holes (first revision)
|
April, 2024
|
-
|
Identical under dual numbering
|
|
|
IS 9549 (Part 2) : 2014 Reviewed In : 2024 |
Fasteners - Bolts, screws and studs - Head slots for bolts (First Revision)
|
April, 2024
|
-
|
Indigenous
|
|
|
IS 9965 : 1981 Reviewed In : 2024 |
Limits of sizes for ISO metric external screw threads for high temperature applications
|
April, 2024
|
-
|
Indigenous
|
|
PGD 37 (22736)
|
Fasteners Mechanical Properties of Corrosion-Resistant Stainless Steel Fasteners Part 6 General Rules for The Selection of Stainless Steels and Nickel Alloys for Fasteners |
|
|
PGD 37 (26457)
Revision of: IS 2609:1972 |
Coach Bolts Specification first revision |
|
|
PGD 37 (26458)
Revision of: IS 3726:2003 |
Thumb screws Specification Second Revision |
|
|
PGD 37 (26459)
Revision of: IS 4040:1998 |
Fasteners Solid Drilled Tubular And Semi-Tubular Rivets Specification First Revision |
|
|
PGD 37 (26641)
IS 4218:2001 |
ISO general purpose inch screw threads Part 1 Basic profile |
|
|
PGD 37 (26642)
|
ISO general purpose inch screw threads Part 2 General plan |
|
|
PGD 37 (26643)
|
ISO general purpose inch screw threads Part 3 Basic dimensions |
|
|
PGD 37 (26644)
|
ISO general purpose inch screw threads Part 4 Allowances and tolerances |
|
PGD 37 (21520)
Revision of: IS 8033:1976 |
Round Washers with Square Hole for Wood Fastenings - Specification |
|
|
PGD 37 (21682)
Revision of: IS 1367:1980 |
Technical Supply Conditions for Threaded Steel Fasteners Part 7 Mechanical Properties and Test Methods for Nuts Without Specified Proof Loads Third Revision |
|
|
PGD 37 (24265)
Revision of: IS 1367:1981 |
Technical Supply Condition for Threaded Steel Fasteners Part 12 Phosphate Coatings on Threaded Fasteners Second Revision |
|
|
PGD 37 (24946)
Revision of: IS 2473:1975 |
Centre Holes Dimensions Second Revision |
PGD 37 (19646) Revision of: IS 2232:1967 |
Slotted and Castle Nuts Specification |
|
PGD 37 (21521) Revision of: IS 5374:1975 |
Taper Washers for I-Beams ISMB - Specification |
|
PGD 37 (26464) Revision of: IS 15629:2005 |
Fasteners Slotted Set Screws with Cone Point Specification first revision |
|
PGD 37 (26465) Revision of: IS 15630:2005 |
Fasteners Slotted set screws with long dog point Specification first revision |
|
PGD 37 (26466) Revision of: IS 15631:2005 |
Fasteners Slotted Set Screws with Cup Point Specification first revision |
|
PGD 37 (18747)
Revision of: IS 866:1957 |
TINMENS RIVETS - SPECIFICATION First Revision of IS 866 |
|
|
PGD 37 (21518)
Revision of: IS 5372:1975 |
Taper Washers for Channels ISMC - Specification |
|
|
PGD 37 (21519)
Revision of: IS 5373:1969 |
Square Washers for Wood Fastenings - Specification |
|
|
PGD 37 (22056)
Revision of: IS 7178:2018 |
Fasteners Heat treated tapping screws Mechanical and physical properties |
|
|
PGD 37 (22057)
Revision of: IS 13726:2018 |
Fasteners Hexagon head bolts with fine pitch thread Product grades A and B Third Revision |
|
|
PGD 37 (26129)
Revision of: IS 6736:1972 |
Slotted Raised Countersunk Head Wood Screw |
|
|
PGD 37 (26130)
Revision of: IS 6739:1972 |
Slotted Round Head Wood Screw |
|
|
PGD 37 (26131)
Revision of: IS 6760:1972 |
Slotted Countersunk Head Wood Screw |
|
|
PGD 37 (26404)
Revision of: IS 13723:2018 |
Hexagon high nuts Style 2 with metric fine pitch thread Product grades A and B Specification third revision |
|
|
PGD 37 (26405)
Revision of: IS 13724:2018 |
Hexagon thin nuts chamfered style 0 with metric fine pitch thread Product grades A and B Specification third revision |
|
|
PGD 37 (26430)
Revision of: IS 4218:2001 |
ISO general purpose metric screw threads Part 1 Basic profile third revision |
|
|
PGD 37 (26432)
Revision of: IS 4218:1999 |
ISO general purpose metric screw threads Part 3 Basic dimensions third revision |
|
|
PGD 37 (26434)
Revision of: IS 4218:2001 |
ISO general purpose metric screw threads Specification Part 4 Selected sizes for screws bolts and nuts third revision |
|
|
PGD 37 (26460)
Revision of: IS 13722:2002 |
Hexagon regular nuts style 1 with metric fine pitch thread Product grades A and B Specification third revision |
PGD 37 (21517)
Revision of: IS 5371:1982 |
Multi-Tooth Lock Washers Specification |
|
PGD 37 (22675)
Revision of: IS 3757:1985 |
High Strength Structural Bolts Specification third revision |
|
PGD 37 (22676)
Revision of: IS 6649:1985 |
Hardened and tempered washers for high strength structural bolts and nuts Specification second revision |
|
PGD 37 (22766)
|
Fasteners Terminology Part 2 Vocabulary and Definitions for Coatings |
|
PGD 37 (22772)
|
Fasteners Terminology Part 4 Control Inspection Delivery Acceptance and Quality |
|
PGD 37 (22813)
Revision of: IS 1364:2018 |
Hexagon head bolts screws and nuts of product grades A and B Part 3 Hexagon nuts style 1 Size range M5 To M39 sixth revision |
|
PGD 37 (25812)
|
Weld Nuts Specification Part 1 Hexagon nuts |
|
PGD 37 (18737)
Revision of: IS 3468:1991 |
Pipe nuts Specification Third Revision | |
|
PGD 37 (19630)
Revision of: IS 1367:2020 |
Technical supply conditions for threaded steel fasteners Part 11 Electroplated coating systems fifth revision | |
|
PGD 37 (22055)
Revision of: IS 1367:2018 |
Technical supply conditions for threaded steel fasteners Part 6 Mechanical properties of fasteners made of carbon steel and alloy steel Nuts with specified property classes fifth revision | |
|
PGD 37 (22752)
Revision of: IS 1364:2003 |
Hexagon head bolts screws and nuts of product grades A and B Part 4 Hexagon thin nuts style 0 Size range M16 to M64 fifth revision | |
|
PGD 37 (22812)
Revision of: IS 1364:2018 |
Hexagon head bolts screws and nuts of product grades A and B Part 6 Hexagon nuts of style 2 second revision | |
|
PGD 37 (25490)
|
Passivation of corrosion-resistant stainless-steel fasteners | |
|
PGD 37 (25501)
|
Countersunk flat head screws Penetration depth of cross recesses | |
|
PGD 37 (25507)
|
Drilling screws with tapping screw thread Mechanical and functional properties |
|
|
IS 1020 : 1963 |
Conversion tables for ordinary use revised |
|
|
IS 10248 : 1982 Reviewed In : 2011 |
Cylindrical Pins with Internal Threads |
|
|
IS 11698 (Part 1) : 2004 Reviewed In : 2019 |
ISO miniature screw threads Part 1 basic profiles First Revision |
|
|
IS 11698 (Part 2) : 2004 Reviewed In : 2019 |
ISO miniature screw threads Part 2 basic dimensions for design profiles First Revision |
|
|
IS 11698 (Part 3) : 2005 Reviewed In : 2015 |
ISO miniature screw threads Part 3 tolerances First Revision |
|
|
IS 11698 (Part 4) : 2005 Reviewed In : 2015 |
ISO miniature screw threads Part 4 limits of sizes First Revision |
|
|
IS 12241 : 1987 Reviewed In : 1998 |
Specification for unplasticized pvc pipes for use in suction and dellvery lines of agricultural pump sets |
|
|
IS 13096 : 2000 ISO 898-6 Reviewed In : 2021 |
Fasteners - Hexagon nuts with specified proof load values - Fine pitch thread - Mechanical properties First Revision |
|
|
IS 1330 : 1958 |
General Plan for Metric Screw Threads With ISO Profile diameter Range 0 25 To 300 Mm |
|
|
IS 1362 : 1962 |
Dimension for Screw Threads for General Purposes diameter Range 1 6 To 39 Mm |
|
|
IS 1363 (Part 3) : 2002 ISO 4034 Reviewed In : 2013 |
Hexagon Head Bolts Screws and Nuts of Product Grade C - Part 3 Hexagon Nuts Size Range M5 to M64 Fourth Revision |
|
|
IS 1367 (Part 14) : 1984 Reviewed In : 2007 |
Technical Supply Conditions for Threaded Steel Fasteners - Part 14 Stainless Steel Threaded Fasteners Second Revision |
|
|
IS 1926 : 1961 |
Equivalent metric units for quantities in mechanical engineering |
|
|
IS 2101 : 1962 |
Recommendations for limits and fits for sizes above 500 mm up to 3150 mm |
|
|
IS 2102 (Part 2) : 1993 ISO 2768-2-89 Reviewed In : 2019 |
General tolerances Part 2 geometrical tolerances for features without individual tolerance indications |
|
|
IS 2388 : 1971 |
Slotted Grub Screws |
|
|
IS 2389 : 1968 |
Precision hexagon bolts screws nuts and lock nuts dia range 1 6 to 5 mm |
|
|
IS 2535 : 1978 Reviewed In : 2001 |
Basic rack and modules of cylindrical gears for general engineering and heavy engineering |
|
|
IS 2614 : 1969 |
Methods for sampling of fasteners |
|
|
IS 2709 : 1993 Reviewed In : 1998 |
Guide for Selection of Fits |
|
|
SP 29-1 : 1985 |
Handbook on Industrial Fasteners Part 1 |
|
|
SP 29-2 : 1987 |
Handbook on Industrial Fasteners - Part 2 Bolts Nuts Screws and other Threaded Fasteners and Washers |
|
|
SP 29-3 : 1987 |
Handbook on Industrial Fastness - Part 3 Rivets Pins Nails Keys and Keyways Cotters and other Non-threaded Fasteners |
|
|
IS 3 : 1949 |
Inch-millimetre Conversion for Industrial use |
|
|
IS 3138 : 1966 Reviewed In : 1996 |
Hexagonal Bolts and Nuts M42 to M150 |
|
|
IS 3139 : 1966 |
Dimensions for screw threads for bolts and nuts dia range M42 to M150 covered in IS 4218 Part 5 |
|
|
IS 3333 (Part 1) : 1967 |
Dimensions for petroleum industry pipe threads Part 1 Line pipe threads |
|
|
IS 3333 (Part 2) : 1967 |
Dimensions for petroleum industry pipe threads Part 2 Casing round threads |
|
|
IS 3333 (Part 3) : 1967 |
Dimensions for petroleum industry pipe threads Part 3 Tubing round threads |
|
|
IS 3333 (Part 4) : 1967 |
Dimensions for petroleum industry pipe threads Part 4 Buttress casing threads |
|
|
IS 3616 : 1966 |
Recommendation on the International system SI units |
|
|
IS/ISO 4033 : 1979 Reviewed In : 2001 |
Industrial Fasteners - Threaded Steel Fasteners - Hexagon Nuts of Style 2 - Product Grade A and B |
|
|
IS 4218 (Part 5) : 1979 Reviewed In : 1996 |
ISO Metric screw threads Part V Tolerances |
|
|
IS 4218 (Part 6) : 1978 Reviewed In : 1996 |
ISO Metric Screw Threads - Part VI Limits of Sizes for Commercial Bolts and Nuts diameter range 1 to 52 mm |
|
|
IS 448 : 1954 |
Unified Screw Threads revised |
|
|
IS 4694 : 1968 Reviewed In : 1996 |
Basic dimensions for square threads |
|
|
IS 5037 : 2002 |
Basic Rack And Modules Of Straight Bevel Gears |
|
|
IS 5308 : 1969 |
Slotted countersunk head and slotted raised countersunk head screws small head series diameter range 1 6 to 6 mm |
|
|
IS 5369 : 1975 Reviewed In : 2021 |
General requirements for plain washers and lock washers First Revision |
|
|
IS 7479 : 1985 Reviewed In : 2011 |
Recess Penetration Gauges |
|
|
IS 7485 : 1985 Reviewed In : 2016 |
Specification for cross recessed countersunk head screws First Revision |
|
|
IS 8192 : 1976 Reviewed In : 1993 |
Guide for selection of fitment bores for cylindrical shaft ends |
|
|
IS 8537 : 1977 Reviewed In : 1996 |
Nomenclature and terminology of fasteners |
|
|
IS 886 : 1957 |
Dimensions for screw threads below 6 mm |
|
|
IS 9549 : 1980 Reviewed In : 2019 |
Dimensions for split pin holes wire holes and head slots for bolts |
|
|
IS 9996 : 1981 Reviewed In : 1996 |
Gauging practice for line pipe threads used in petroleum industry |
|
IS 10238 : 2001 Reviewed In : 2021 |
Fasteners - Threaded steel fasteners - Step bolts for steel structures - Specification First Revision |
|
|
IS 10248 (Part 1) : 2011 Reviewed In : 2021 |
Parallel pins with internal thread Part 1 unhardened steel and austenitic stainless steel First Revision |
|
|
IS 10248 (Part 2) : 2011 Reviewed In : 2021 |
Parallel pins with internal thread Part 2 hardened steel and martensitic stainless steel First Revision |
|
|
IS 1120 : 1975 Reviewed In : 2021 |
Specification for coach screws First Revision |
|
|
IS 12427 : 2001 Reviewed In : 2021 |
Fasteners - Threaded steel fasteners - Hexagon head transmission tower bolts - Specification First Revision |
|
|
IS 12952 : 2005 ISO 8740 Reviewed In : 2021 |
Grooved pins - Full - Length parallel grooved with chamfer First Revision |
|
|
IS 12982 : 1991 ISO 8749 Reviewed In : 2021 |
Pins and grooved pins - Shear test |
|
|
IS 1363 (Part 1) : 2023 ISO 4016 : 2022 |
Hexagon head bolts screws and nuts of product grade C Part 1 Hexagon head bolts Size range M5 to M64 sixth revision |
|
|
IS 1363 (Part 2) : 2023 ISO 4018 : 2022 |
Hexagon head bolts screws and nuts of product grade C Part 2 Hexagon head screws Size range M5 to M64 sixth revision |
|
|
IS 1364 (Part 1) : 2023 ISO 4014 : 2022 |
Hexagon head bolts screws and nuts of property grades A and B Part 1 Hexagon head bolts Size range M1 6 to M64 sixth revision |
|
|
IS 1364 (Part 2) : 2023 ISO 4017 : 2022 |
Hexagon head bolts screws and nuts of product grades A and B Part 2 Hexagon head screws Size range M1 6 to M64 Sixth revision of IS 1364 Part 2 |
|
|
IS 1364 (Part 3) : 2018 Reviewed In : 2023 |
Hexagon Head Bolts Screws and Nuts of Product Grades A and B Part 3 Hexagon Nuts Style 1 Size Range M 1 6 To M 64 |
|
|
IS 1364 (Part 4) : 2003 ISO 4035 Reviewed In : 2023 |
Hexagon head bolts screws and nuts of product grades A and B Part 4 hexagon thin nuts Chamfered Size Range M1 6t0 M64 Fourth Revision |
|
|
IS 1364 (Part 6) : 2018 ISO 4033 : 2012 Reviewed In : 2023 |
Hexagon Head Bolts Screws and Nuts of Product Grades A and B Part 6 Hexagon Nuts Style 2 First Revision |
|
|
IS 1365 : 2022 ISO 2009 : 2011 |
Slotted countersunk flat head screws Product grade A Fifth Revision of IS 1365 |
|
|
IS 1366 : 2022 ISO 1207 : 2011 |
Slotted Cheese Head Screws Product Grade A Fourth Revision of IS 1366 |
|
|
IS 1367 (Part 3) : 2017 ISO 898-1 : 2013 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners Part 3 mechanical properties of fasteners made of carbon steel and bolts screws and studs Fifth Revision |
|
|
IS 1367 (Part 5) : 2018 ISO 898-5 : 2012 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners Part 5 mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread Fourth Revision |
|
|
IS 1367 (Part 6) : 2018 ISO 898-2 : 2012 Reviewed In : 2024 |
Technical supply conditions for threaded steel fasteners Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread Fourth Revision |
|
|
IS 1367 (Part 7) : 1980 Reviewed In : 2023 |
Technical supply conditions for tHreadeD steel fasteners Part 7 mechanical properties and test methods for nuts without specified proof loads Second Revision |
|
|
IS 1367 (Part 8) : 2020 ISO 2320 : 2015 Reviewed In : 2024 |
Technical Supply Conditions for Threaded Steel Fasteners Part 8 Prevailing Torque Type Steel Nuts Functional Properties Fifth Revision |
|
|
IS 1367 (Part 14/Sec 1) : 2023 ISO 3506-1 : 2020 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless Steel Fasteners Section 1 Bolts screws and studs with specified grades and property classes Fifth Revision of IS 1367 Part 14 Sec 1 |
|
|
IS 1367 (Part 14/Sec 2) : 2023 ISO 3506-2 : 2020 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless steel Fasteners Section 2 Nuts with specified grades and property classes |
|
|
IS 1367 (Part 14/Sec 3) : 2018 ISO 3506-3 : 2009 Reviewed In : 2023 |
Technical supply conditions for threaded steel fasteners Part 14 mechanical properties of corrosion - Resistant stainless steel fasteners section 3 set screws and similar fasteners not under tensile stress Fourth Revision |
|
|
IS 1368 : 2018 ISO 4753 : 2011 Reviewed In : 2023 |
Dimensions for ends of parts with external ISO metric threads Fourth Revision |
|
|
IS 13722 : 2002 ISO 8673 : 2012 Reviewed In : 2023 |
Hexagon regular nuts Style 1 with metric fine pitch thread - Product grades A and B Second Revision |
|
|
IS 13723 : 2018 ISO 8674 : 2012 Reviewed In : 2024 |
Hexagon High Nuts Style 2 With Metric Fine Pitch Thread - Product Grades A and B Second Revision |
|
|
IS 13724 : 2018 ISO 8675 : 2012 Reviewed In : 2024 |
Hexagon thin nuts chamfered Style 0 with metric fine pitch thread - Product grades A and B Second Revision |
|
|
IS 13726 : 2023 ISO 8765 : 2022 |
Hexagon head bolts with metric fine pitch thread Product grades A and B third revision |
|
|
IS 14394 : 1996 Reviewed In : 2021 |
Industrial fasteners - Hexagon nuts of product grade C - Hot - Dip galvanized - Specification Size Range M12 To M36 |
|
|
IS 14894 : 2023 ISO/FDIS 4015 : 2021 |
Fasteners Hexagon head bolts of product grade B Reduced shank shank diameter pitch diameter Specification |
|
|
IS 15581 : 2018 ISO 4161 : 2012 Reviewed In : 2023 |
Hexagon nuts with flange style 2 - Coarse thread First Revision |
|
|
IS 15582 : 2018 ISO 4162 : 2012 Reviewed In : 2023 |
Hexagon Bolts with Flange - Small Series - Product Grade A with Driving Feature of Product Grade B First Revision |
|
|
IS 15628 : 2022 ISO 4766 : 2011 |
Slotted set screws with flat point - Specification First Revision of IS 15628 ICS 2106010 |
|
|
IS 15629 : 2005 ISO 7434 Reviewed In : 2021 |
Slotted set screws with cone point |
|
|
IS 15630 : 2005 ISO 7435 Reviewed In : 2021 |
Slotted set screws with long dog point |
|
|
IS 15631 : 2005 ISO 7436 Reviewed In : 2021 |
Slotted set screws with cup point |
|
|
IS 18471 (Part 1) : 2023 ISO 15481:1999 |
Fasteners Cross Recessed Drilling Screws with Tapping Screw Thread Part 1 Pan Head |
|
|
IS 18471 (Part 2) : 2023 ISO 15482:1999 |
Fasteners Cross Recessed Drilling Screws with Tapping Screw Thread Part 2 Countersunk Head |
|
|
IS 18471 (Part 3) : 2023 ISO 15483:1999 |
Fasteners Cross Recessed Drilling Screws with Tapping Screw Thread Part 3 Raised Countersunk Head |
|
|
IS 18476 : 2023 ISO 15480:2019 |
Fasteners Hexagon Washer Head Drilling Screws with Tapping Screw Thread |
|
|
IS 18480 (Part 1) : 2023 ISO 7049 : 2011 |
Cross Recessed Tapping Screws Part 1 Pan Head |
|
|
IS 18480 (Part 2) : 2023 ISO 7050 : 2011 |
Cross Recessed Tapping Screws Part 2 Countersunk Flat Head |
|
|
IS 18480 (Part 3) : 2023 ISO 7051 : 2011 |
Cross Recessed Tapping Screw Part 3 Raised Countersunk Oval Head |
|
|
IS 18507 : 2024 |
Drywall Screws Specification |
|
|
IS 18508 : 2024 |
Chipboard Screws Specification |
|
|
IS 18509 : 2024 |
Cross-recessed Countersunk Head Wood Screws Specification |
|
|
IS 18741 : 2024 |
Concrete Nails Specification |
|
|
IS 1928 : 1961 Reviewed In : 2021 |
Specification for boiler rivets 12 To 48 Mm Diameter |
|
|
IS 1929 : 1982 Reviewed In : 2021 |
Specification for hot forged steel rivets for hot closing 12 To 36 Mm Diameter |
|
|
IS 2016 : 1967 Reviewed In : 2021 |
Specification for plain washers First Revision |
|
|
IS 207 : 1964 Reviewed In : 2021 |
Specification for gate and shutter hooks and eyes Revised |
|
|
IS 2155 : 1982 Reviewed In : 2021 |
Specification for cold forged solid steel rivets for hot closing 6 To 16 Mm Diameter First Revision |
|
|
IS 2232 : 1967 Reviewed In : 2021 |
Specification for slotted and castle nuts First Revision |
|
|
IS 2269 : 2006 ISO 4762 Reviewed In : 2021 |
Hexagon socket head cap screws Fifth Revision |
|
|
IS 2585 : 2006 Reviewed In : 2021 |
Square head bolts screws and square nuts of product grade C - Specification Second Revision |
|
|
IS 2609 : 1972 Reviewed In : 2024 |
Specification for coach bolts First Revision |
|
|
IS 2636 : 1972 Reviewed In : 2021 |
Specification for wing nuts First Revision |
|
|
IS 2638 : 1974 Reviewed In : 2021 |
Specification for flat split cotters First Revision |
|
|
IS 2687 : 1991 Reviewed In : 2021 |
Capnuts - Specification Second Revision |
|
|
IS 3063 : 1994 Reviewed In : 2021 |
Fasteners - Single coil rectangular section spring lock washers specification Second Revision |
|
|
IS 3458 : 2018 ISO 1119 : 2011 Reviewed In : 2023 |
Conical tapers and taper angles for general engineering purposes Third Revision |
|
|
IS 3460 : 1991 Reviewed In : 2021 |
Knurled nuts - Specification Second Revision |
|
|
IS 3468 : 1991 Reviewed In : 2021 |
Pipe nuts - Specification Second Revision |
|
|
IS 3524 (Part 1) : 1982 Reviewed In : 2021 |
Specification for threaded taper pins Part 1 with internal threads First Revision |
|
|
IS 3524 (Part 2) : 1982 Reviewed In : 2021 |
Specification for threaded taper pins Part 2 with external threads First Revision |
|
|
IS 3640 : 1982 Reviewed In : 2021 |
Specification for hexagon fit bolts First Revision |
|
|
IS 3726 : 2003 Reviewed In : 2024 |
Thumb screws - Specification Second Revision |
|
|
IS 3727 : 1966 Reviewed In : 2021 |
Specification for wing screws |
|
|
IS 3757 : 1985 Reviewed In : 2019 |
Specification for high strength structural bolts Second Revision |
|
|
IS 3974 : 1967 Reviewed In : 2021 |
Specification for bifurcated rivets for general purposes |
|
|
IS 4040 : 1998 Reviewed In : 2024 |
Fasteners - Solid drilled tubular and semi - Tubular rivets - Specification First Revision |
|
|
IS 4732 : 1968 Reviewed In : 2021 |
Specification for rivets for shipbuilding |
|
|
IS 5368 : 1969 Reviewed In : 2021 |
Specification for thin slotted and castle nuts Dia Range 6 To 52 Mm |
|
|
IS 5370 : 1969 Reviewed In : 2021 |
Specification for plain washers with outside diameter 3 x inside diameter |
|
|
IS 5371 : 1982 Reviewed In : 2021 |
Specification for multi - Tooth lock washers First Revision |
|
|
IS 5372 : 1975 Reviewed In : 2021 |
Specification for taper washers for channels ISMC First Revision |
|
|
IS 5373 : 1969 Reviewed In : 2021 |
Specification for square washers for wood fastenings |
|
|
IS 5374 : 1975 Reviewed In : 2021 |
Specification for taper washers for I - Beams Ismb First Revision |
|
|
IS 549 : 2005 Reviewed In : 2021 |
Split pins - Specification Third Revision |
|
|
IS 5554 : 1991 Reviewed In : 2021 |
Lock washers with lug - Specification First Revision |
|
|
IS 5556 : 1991 Reviewed In : 2021 |
Serratedlockwashers - Specification First Revision |
|
|
IS 5624 : 2021 |
FOUNDATION BOLTS SPECIFICATION Second Revision |
|
|
IS 6101 : 2018 ISO 1580 : 2011 Reviewed In : 2023 |
Slotted pan head screws - Product grade a Third Revision |
|
|
IS 6113 : 1970 Reviewed In : 2021 |
Specification for aluminium fasteners for buildin - g purposes |
|
|
IS 6610 : 1972 Reviewed In : 2021 |
Specification for heavy washers for steel structures |
|
|
IS 6623 : 2004 Reviewed In : 2021 |
High Strength Structural Nuts |
|
|
IS 6639 : 1972 Reviewed In : 2021 |
Specification for hexagon bolts for steel structures |
|
|
IS 6649 : 1985 Reviewed In : 2021 |
Specification for hardened and tempered washers for high strength structural bolts and nuts First Revision |
|
|
IS 6730 : 1972 Reviewed In : 2021 |
Specification for felt nails |
|
|
IS 6732 : 1972 Reviewed In : 2021 |
Specification for double point nails |
|
|
IS 6733 : 1972 Reviewed In : 2021 |
Specification for wall and roofing nails |
|
|
IS 6734 : 1972 Reviewed In : 2021 |
Specification for cut lath and lath nails |
|
|
IS 6735 : 1994 Reviewed In : 2019 |
Fasteners - Spring lock wasixers for screws with cylindrical heads - Specification First Revision |
|
|
IS 6736 : 1972 Reviewed In : 2021 |
Specification for slotted raised countersunk head wood screws |
|
|
IS 6738 : 1972 Reviewed In : 2021 |
Specification for panel pins and lost head nails |
|
|
IS 6739 : 1972 Reviewed In : 2021 |
Slotted Round Head Wood Screws |
|
|
IS 6755 : 1980 Reviewed In : 2021 |
Specification for double coil helical spring washers First Revision |
|
|
IS 6761 : 2023 ISO 10642 : 2019 |
Fasteners Hexagon Socket Countersunk Head Screws with Reduced Loadability Third Revision of IS 6761 |
|
|
IS 7002 : 2018 ISO 7040 : 2012 Reviewed In : 2023 |
Prevailing torque type hexagon regular nuts With Non - Metallic Insert - Property classes 5 8 and 10 Third Revision |
|
|
IS 7169 : 2018 ISO 1483-2011 Reviewed In : 2023 |
Slotted raised countersunk Oval head tapping screws Second Revision |
|
|
IS 7170 : 2018 ISO 1482-2011 Reviewed In : 2023 |
Slotted countersunk Flat head tapping screws Second Revision |
|
|
IS 7173 : 2018 ISO 1481-2011 Reviewed In : 2023 |
Slotted pan head tapping screws Second Revision |
|
|
IS 7178 : 2018 ISO 2702 : 2011 Reviewed In : 2024 |
Heat - Treated steel tapping screws - Mechanical properties Fourth Revision |
|
|
IS 723 : 2023 |
Steel Countersunk Head Wire Nails Specification Second Revision |
|
|
IS 724 : 2023 |
Mild Steel and Brass Cup Ruler and Square Hooks and Screw Eyes Specification |
|
|
IS 725 : 1961 Reviewed In : 2021 |
Specification for copper wire nails Revised |
|
|
IS 730 : 2021 |
Specification for Hook Bolts for Corrugated Sheet Roofing |
|
|
IS 7483 : 2018 Reviewed In : 2023 |
Pan Head Screws With Type H or Type Z Cross Recess - Product Grade A Third Revision |
|
|
IS 7485 (Part 1) : 2018 ISO 7046-1 : 2011 Reviewed In : 2023 |
Countersunk Flat Head Screws Common head Style With Type H or Type Z Cross Recess - Product Grade A Part 1 Steel Screws of Property Class 4 8 Third Revision |
|
|
IS 7485 (Part 2) : 2018 ISO 7046-2 : 2011 Reviewed In : 2023 |
Countersunk flat head screws common head style with type H or Type Z Cross Recess - Product Grade A part 2 Steel Screws of Property Class 8 8 Stainless Steel Screws and Non - Ferrous Metal Screws Third Revision |
|
|
IS 7486 : 2018 ISO 7047 : 2011 Reviewed In : 2023 |
Raised countersunk head screws Common Head Style with type H or type Z cross recess - Product grade A Third Revision |
|
|
IS 7519 : 1974 Reviewed In : 2021 |
Specification for hammer drive screws |
|
|
IS 7790 : 1991 Reviewed In : 2021 |
Domed cap nuts - Specification First Revision |
|
|
IS 7795 : 2004 Reviewed In : 2021 |
Hexagon nuts with collar - Specification First Revision |
|
|
IS 8033 : 1976 Reviewed In : 2021 |
Specification for round washers with square hole for wood fastenings |
|
|
IS 8068 : 1976 Reviewed In : 2021 |
Specification for tab washers |
|
|
IS 8070 : 1991 Reviewed In : 2021 |
Screws - Slotted capstan Tommy bolts - Specification First Revision |
|
|
IS 8351 : 1977 Reviewed In : 2021 |
Specification for spiral pins Heavy Duty Type |
|
|
IS 8352 : 1977 Reviewed In : 2021 |
Specification for flat countersunk square neck bolts |
|
|
IS 8353 : 1977 Reviewed In : 2021 |
Specification for flat countersunk nib bolts |
|
|
IS 8379 : 1977 Reviewed In : 2021 |
Specification for spiral pins Medium - Duty Type |
|
|
IS 8412 : 1977 Reviewed In : 2021 |
Specification for slotted countersunk head bolts for steel structures |
|
|
IS 866 : 1957 Reviewed In : 2021 |
Specification forTinmens Rivets |
|
|
IS 8721 : 1978 Reviewed In : 2021 |
Specification for fish bolts Cup Oval Neck Bolts for collieries |
|
|
IS 8722 : 1978 Reviewed In : 2021 |
Specification for fish bolts with square head |
|
|
IS 8822 : 1978 Reviewed In : 2021 |
Specification for slotted mushroom head roofing bolts |
|
|
IS 8856 : 1991 Reviewed In : 2019 |
Hexagon weld nuts - Specification First Revision |
|
|
IS 8869 : 1978 Reviewed In : 2021 |
Specification for washers for corrugated sheet roofing |
|
|
IS 8911 : 2018 ISO 2010 : 2011 Reviewed In : 2023 |
Slotted raised countersunk head screws - Product grade A Second Revision |
|
|
IS 9519 : 2005 Reviewed In : 2021 |
Fasteners - Hexagon products - Width across flats First Revision |
|
|
IS 9549 (Part 1) : 2014 ISO 7378:1983 Reviewed In : 2024 |
Fasteners -- Bolts screws and studs Part 1 Split pin holes and wire holes first revision |
|
|
IS 9549 (Part 2) : 2014 Reviewed In : 2024 |
Fasteners - Bolts screws and studs - Head slots for bolts First Revision |