|
1 |
IS 10988 : 1984 |
Method of measuring noise from machine tools (excluding testing in anechoic chambers) |
Methods of tests |
NA |
|
2 |
IS 11118 : 1997 |
Guidelines for technical evaluation of general purpose parallel lathes |
Others |
NA |
|
3 |
IS 11398 : Part 1 : 1985 |
Test chart for horizontal spindle capstan, turret and single spindle automatic lathes:Part 1 Machinable bar diameters greater than 25 mm |
Product Specification |
IS 11398 : 2018/ISO 6155 : 1998 |
|
4 |
IS 11398 : Part 2 : 1992 |
Test charts for horizontal spindle capstain, turret and single spindle automatic lathes Part 2 Machinable bar dia. 25 mm or less and chuck dia. upto 160 mm |
Product Specification |
IS 11398 : 2018/ISO 6155 : 1998 |
|
5 |
IS 12454 : 1988 |
Guidelines for Technical Evaluation of General Purpose Parallel Lathes with Swing over Bed above 800 mm |
------ |
IS 11118 |
|
6 |
IS 12525 : 1989 |
Snap Rings |
Product Specification |
------ |
|
7 |
IS/ISO 13041 : Part 1 : 2004 |
Test Conditions for Numericallly Controled Turning Machines and Turning Centres Part 1 Geometric Tests for Machines with a Horizontal Workholding Spindle |
Code of Practice |
IS/ISO13041-1:2020 |
|
8 |
IS/ISO 13041 : Part 2 : 2008 |
Test conditions for numerically controlled turning machines and turning centres: Part 2 geometric tests for machines with a vertical workholding spindle |
Code of Practice |
IS/ISO 13041 (Part 2):2020 |
|
9 |
IS 13634 : 1993 |
General introduction for milling machines with table of variable height, with horizontal or vertical spindle |
Others |
DECIDED BY DIVISIONAL COUNCIL - 16 MAR 2015 |
|
10 |
IS 13640 : 1993 |
General introduction for milling machines with table of fixed height, with horizontal or vertical spindle |
Others |
IS/ISO 1984-2 : 2011 |
|
11 |
IS 13993 : 1994 |
Test chart for universal milling machine with a swivelling table |
Product Specification |
NA |
|
12 |
IS 15248 : 2002 |
Self-Centring Chucks for Machine Tools with Two-Piece Jaws (Tongue and Groove Type) - Sizes for Interchangeability and Acceptance Test Specifications |
Dimensions |
IS/ISO 1701-2 : 2004, IS 15248(PART 1) : 2013/ISO 3442-1 : 2005, IS 15248(PART 2) : 2013/ISO 3442-2 : 2005&IS 15248(PART 3) : 20 |
|
13 |
IS 15249 : 2002 |
Machine tools - Jaw mountings on power chucks |
Dimensions |
DECIDED BY DIVISIONAL COUNCIL - 5 APR 2016 |
|
14 |
IS 15250 : Part 7 : 2018 |
Test conditions for machining centres: Part 7 accuracy of finished test pieces |
Code of Practice |
IS 15250(Part 7):2023 |
|
15 |
IS 1995 : 1984 |
Overall internal heights for lathe tool posts |
Dimensions |
------ |
|
16 |
IS 2063 : 1988 |
Acceptance code for machine tools - Geometric accuracy of machines operating under no-load or finishing conditions |
------ |
------ |
|
17 |
IS 2063 : Part 3 : 2016 |
Test code for machine tools: Part 3 determination of thermal effects |
Code of Practice |
IS 2063(Part 3):2023 |
|
18 |
IS 2063 : Part 4 : 2016 |
Test code for machine tools: Part 4 circular tests for numerically controlled machine tools |
Code of Practice |
IS 2063(Part 4):2023 |
|
19 |
IS 2063 : Part 7 : 2016 |
Test code for machine tools: Part 7 geometric accuracy of axes of rotation |
Code of Practice |
IS 2063(Part 7):2023 |
|
20 |
IS 2200 : 1994 |
Test chart for milling machines with table of variable height, with horizontal spindle (Third Revision) |
------ |
------ |
|
21 |
IS 2200 : Part 2 : 2002 |
Test Conditions for Milling Machines with Table of Variable Height - Testing of Accuracy - Part 2 : Machines with Horizontal Spindle |
Others |
IS/ISO 1701-1 : 2004 |
|
22 |
IS 2200 : Part 3 : 2002 |
Test Conditions for Milling Machines with Table of Variable Height - Testing of Accuracy - Part 3 : Machines with Vertical Spindle |
Others |
IS/ISO 1701-2 : 2004, IS 15248(PART 1) : 2013/ISO 3442-1 : 2005, IS 15248(PART 2) : 2013/ISO 3442-2 : 2005&IS 15248(PART 3) : 20 |
|
23 |
IS 2201 : 1994 |
Test Chart for Milling Machines with Table of Variable Height, with Vertical Spindle |
------ |
------ |
|
24 |
IS 2308 : 1989 |
Test Chart For Slotting Machines |
Product Specification |
NA |
|
25 |
IS 2310 : 1989 |
Test chart for shaping machines |
Product Specification |
NA |
|
26 |
IS 2392 : 1963 |
Sizes for General Purpose Lathes |
------ |
------ |
|
27 |
IS 2538 : 1963 |
Test chart for bench grinders |
Product Specification |
NA |
|
28 |
IS 2582 : Part 3 : 1987 |
Machine tools - Spindle noses and face plates - Sizes for interchangeability: Part 3 bayonet type (Second Revision) |
Code of Practice |
IS 2582(Part 3):2023 |
|
29 |
IS 2583 : 1963 |
Dimensions for Camlock Type Spindle Nose and Back Plates |
------ |
IS 2582 |
|
30 |
IS 2743 : 1992 |
Test chart for surface grinding machines with horizontal grinding wheel spindle and reciprocating table (Second Revision) |
Product Specification |
DECIDED BY DIVISIONAL COUNCIL - 16 MAR 2015 |
|
31 |
IS 2793 : 1964 |
Dimensions of Cranked Handles |
------ |
------ |
|
32 |
IS 2876 : 1999 |
3 - Jaw and 4 - Jaw scroll manually operated self - Centering lathe chucks - Specification (Second Revision) |
Product Specification |
------ |
|
33 |
IS 2904 : 1998 |
Ball handles |
Product Specification |
NA |
|
34 |
IS 2908 : 1998 |
Hand cranks |
------ |
------ |
|
35 |
IS 2975 : 1998 |
Control levers with ball grip |
Product Specification |
NA |
|
36 |
IS 2996 : 1986 |
Mounting dimensions of plain grinding wheels by means of hub flanges |
Dimensions |
NA |
|
37 |
IS 3405 : 1966 |
Test chart for power hacksaw machines (up to 300 mm round bar capacity) |
Product Specification |
NA |
|
38 |
IS 4279 : 1984 |
Goose Neck Clamps |
Product Specification |
NA |
|
39 |
IS 4292 : 1984 |
Strap Clamps |
Product Specification |
NA |
|
40 |
IS 4293 : 1984 |
U-type Clamps |
Product Specification |
NA |
|
41 |
IS 4537 : 1968 |
Test Chart for Capstan and Turret lathes |
------ |
------ |
|
42 |
IS 4872 : 1968 |
Sizes for Planning Machines |
------ |
------ |
|
43 |
IS 5091 : 1969 |
Dimensions For Circular Base Plates |
Dimensions |
NA |
|
44 |
IS 5092 : 1969 |
Dimensions for square and rectangular base plates |
Dimensions |
NA |
|
45 |
IS 5095 : 1998 |
End locating plugs |
Product Specification |
NA |
|
46 |
IS 5096 : 1969 |
Dimensions for round locating studs |
Dimensions |
NA |
|
47 |
IS 5097 : 1969 |
Dimensions for diamond locating studs |
Dimensions |
NA |
|
48 |
IS 519 : 1954 |
T-bolts and T-nuts |
------ |
IS 2013, IS 2014, IS 2015 |
|
49 |
IS 5250 : 1984 |
Swing Clamps |
Product Specification |
NA |
|
50 |
IS 5251 : 1984 |
Table Clamps |
Product Specification |
NA |
|
51 |
IS 5252 : 1984 |
Dimensions for Wide Clamp Plates |
Dimensions |
NA |
|
52 |
IS 5990 : 1971 |
Sizes for Shaping Machines |
------ |
------ |
|
53 |
IS 5998 : 1984 |
Parallel Sided Clamp Plates |
Product Specification |
NA |
|
54 |
IS 5999 : 1999 |
Swing Latches |
Product Specification |
NA |
|
55 |
IS/ISO 6779 : 1981 |
ACCEPTANCE CONDITIONS FOR BROACHING MACHINES OF VERTICAL INTERNAL TYPE — TESTING OF ACCURACY |
Service Specification |
NULL |
|
56 |
IS 6893 : Part 1 : 1988 |
Proforma for purchase Specification for machine tools: Part 1 general purpose parallel lathes and precision lathes (First Revision) |
Others |
Decided by Council |
|
57 |
IS 6893 : Part 2 : 1987 |
Proforma for purchase Specification for machine tools: Part 2 horizontal/universal knee - Type milling machines (First Revision) |
Others |
Decided by Council |
|
58 |
IS 6893 : Part 3 : 1988 |
Proforma for purchase Specification for machine tools: Part 3 radial drilling machines (First Revision) |
Others |
Decided by Council |
|
59 |
IS 6893 : Part 4 : 1987 |
Proforma for purchase Specification for machine tools: Part 4 vertical turning and boring lathes (First Revision) |
Others |
Decided by Council |
|
60 |
IS 6893 : Part 5 : 1987 |
Proforma for purchase Specification for machine tools: Part 5 milling machine with table of variable height with vertical spindle (First Revision) |
Others |
Decided by Council |
|
61 |
IS 6893 : Part 6 : 1985 |
Proforma for purchase Specification for machine tools: Part 6 bench/pillar type drilling machines |
Others |
Decided by council |
|
62 |
IS 6893 : Part 7 : 1990 |
Proforma for purchase Specification for machine tools: Part 7 external cylindrical grinding machines with horizontal spindle |
Others |
Decided by council |
|
63 |
IS 6893 : Part 8 : 1992 |
Proforma for purchase Specification for machine tools: Part 8 internal cylindrical grinding machines with horizontal spindle |
Others |
Decided by council |
|
64 |
IS 6893 : Part 9 : 1990 |
Proforma for purchase Specification for machine tools: Part 9 surface grinders with horizontal axis |
Others |
Decided by council |
|
65 |
IS 6893 : Part 10 : 1992 |
Proforma for purchase Specification for machine tools: Part 10 copying lathes |
Others |
Decided by council |
|
66 |
IS 6893 : Part 11 : 1992 |
Proforma for purchase Specification for machine tools: Part 11 capstan and turret lathes |
Others |
Decided by council |
|
67 |
IS 6893 : Part 12 : 1992 |
Proforma for purchase Specification for machine tools: Part 12 horizontal boring and milling machines (Table Type) |
Others |
Decided by council |
|
68 |
IS 7227 : 1974 |
Recommended diameters of wheels for woodworking table bandsawing machines |
Others |
NA |
|
69 |
IS 7229 : 1974 |
Recommended working level heights for woodworking machines |
Others |
NA |
|
70 |
IS 7287 : 1974 |
Recommended working dimensions of woodworking machines |
Others |
NA |
|
71 |
IS/ISO 7572 : 1984 |
Conditions of Acceptance and Installation for Work-holding Fixed Tables of Machine Tools |
Others |
------ |
|
72 |
IS 7764 : 1975 |
Sizes for Drilling Machine |
------ |
------ |
|
73 |
IS 7765 : 1975 |
Sizes for Milling Machines with Table fo Various Height with Horizontal or Vertical Spindle |
------ |
------ |
|
74 |
IS 7936 : 1976 |
Sizes for Redial Drilling Machines |
------ |
------ |
|
75 |
IS 8099 : 1976 |
Sizes of collars for circular saw blades for woodworking machines |
Dimensions |
NA |
|
76 |
IS 8131 : 1976 |
Test chart for circular tables for machine tools (table diameter up to 630 mm) |
Product Specification |
NA |
|
77 |
IS 9809 : 1981 |
Test chart for crankshaft grinding machines |
Product Specification |
IS 2368 : 2018 |
