| SNo |
IS Number |
Title |
Technical Committee |
|
1 |
IS 209 : 1992 |
Zinc ingot - Specification (Fourth Revision) |
MTD 9 |
|
2 |
IS 226 : 1975 |
Structural steel (Standard quality) |
MTD 4 |
|
3 |
IS 410 : 1977 |
Specification for cold rolled brass sheet, strip and foil (Third Revision) |
MTD 8 |
|
4 |
: |
|
|
|
5 |
IS 1573 : 1986 |
Specification for electroplated coatings of zinc on iron and steel (Second Revision) |
MTD 24 |
|
6 |
IS 1865 : 1991 |
Iron castings with spheroidal or nodular graphite - Specification (Third Revision) |
MTD 6 |
|
7 |
IS 2004 : 1991 |
Carbon steel forgings for general engineering purposes - Specification (Third Revision) |
MTD 16 |
|
8 |
IS 2107 : 1977 |
Whiteheart malleable iron castings |
MTD 6 |
|
9 |
IS 2108 : 1977 |
Blackheart Malleable Iron Castings |
MTD 6 |
|
10 |
IS 2121 : Part 1 : 1981 |
Specification for conductors and earth wire accessories for overhead power lines: Part 1 armour rods, binding wires and tapes for conductors (First Revision) |
ETD 37 |
|
11 |
IS 2121 : Part 2 : 1981 |
Specification for conductors and earth wire accessories for overhead power lines: Part 2 mid - Spain joints and repair sleeves - For conductors (First Revision) |
ETD 37 |
|
12 |
IS 2486 : Part 2 : 1989 |
Insulator fittings for overhead power lines with nominal voltage greater than 1 000 V - Specification: Part 2 dimensional requirements (Second Revision) |
ETD 6 |
|
13 |
IS 2486 : Part 3 : 1974 |
Specification for insulator fittings for overhead power lines with a nominal voltage greater than 1 000 volts: Part 3 locking devices |
ETD 6 |
|
14 |
IS 2629 : 1985 |
Recommended practice for hot-dip galvanizing of iron and steel (First Revision) |
MTD 24 |
|
15 |
IS 2633 : 1986 |
Method for testing uniformity of coating on zinc coated articles (Second Revision) |
MTD 24 |
|
16 |
IS 4759 : 1996 |
Hot - Dip zinc coatings on structural steel and other allied products - Specification (Third Revision) |
MTD 24 |
|
17 |
IS 4905 : 2015 |
Random sampling and randomization procedures (First Revision) |
MSD 3 |
|
18 |
IS 5082 : 1998 |
Wrought aluminium and aluminium alloy bars, rods, tubes, sections, plates and sheets for electrical applications (Second Revision) |
MTD 7 |
|
19 |
IS 7814 : 2005 |
Phosphor bronze sheet, strip and foil - Specification (Second Revision) |
MTD 8 |
|
20 |
IS 5522 : 2014 |
Stainless steel sheets and strips for utensils - Specification (Third Revision) |
MTD 16 |
|
21 |
IS 5561 : 2018 |
Electric power connectors - Specification (First Revision) |
ETD 8 |
|
22 |
IS 6051 : 1970 |
Code for designation of aluminium and its alloys |
MTD 7 |
|
23 |
IS 6603 : 2001 |
Stainless steel bars and flats - Specification (First Revision) |
MTD 16 |
|
24 |
IS 1367 : Part 1 : 2014 |
Technical supply conditions for threaded steel fasteners: Part 1 general requirements for bolts, screws, studs and nuts (Fourth Revision) |
PGD 37 |
|
25 |
IS 1367 : Part 6 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision) |
PGD 37 |
|
26 |
IS 1875 : 1992 |
Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision) |
MTD 4 |
