| SNo |
IS Number |
Title |
Technical Committee |
| 1 |
IS 9574 : 2004 |
Leaf springs assembly clips - Specification (Second Revision) |
TED 34 |
| 2 |
IS 8711 : 2002 |
Gap frame open front mechanical presses - Capacity ratings and dimensions (First Revision) |
PGD 4 |
| 3 |
IS 5703 : 1988 |
Specification for countersinks 90° with morse taper shanks and detachable pilots (first revision) |
PGD 32 |
| 4 |
IS 5704 : 1988 |
Specification for counterbores with parallel shanks and solid pilots (first revision) |
PGD 32 |
| 5 |
IS 10431 : 1994 |
Measurement of air flow of compressors and exhausters by nozzles (First Revision) |
MED 22 |
| 6 |
IS 9999 : 1981 |
Specification for diesel locomotives for use in mines |
MED 8 |
| 7 |
IS 1367 : Part 19 : 1997 |
Industrial fasteners - Threaded steel fasteners - Technical supply conditions: Part 19 axial load fatigue testing of bolts, screws and studs |
PGD 37 |
| 8 |
IS 3406 : Part 1 : 1986 |
Dimensions for countersinks and counterbores: Part 1 countersinks (Second Revision) |
PGD 37 |
| 9 |
IS 3406 : Part 2 : 2014 |
Dimensions for countersinks and counterbores: Part 2 counterbores (Third Revision) |
PGD 37 |
| 10 |
IS 5372 : 1975 |
Specification for taper washers for channels (ISMC) (First Revision) |
PGD 37 |
| 11 |
IS 5374 : 1975 |
Specification for taper washers for I - Beams (Ismb) (First Revision) |
PGD 37 |
| 12 |
IS 5240 : 1969 |
SpeclFication for cast skew bollards |
TED 17 |
| 13 |
IS 13139 : 1992 |
End - Suction centrifugal pumps - Baseplate and installation dimensions |
MED 20 |
| 14 |
IS/IEC 60079 : PART 0 : 2017 |
Explosive Atmospheres Part 0 Equipment — General Requirements ( Third Revision ) |
ETD 22 |
| 15 |
IS/IEC 61241 : PART 0 : 2004 |
Electrical apoparatus for use in the presence of compustible dust : Part 0 General requirements |
ETD 22 |
| 16 |
IS 13090 : 2018 |
Automotive vehicles - Commercial vehicles - Clutch housings - Dimensions (First Revision) |
TED 2 |
| 17 |
IS 16793 : Part 3 : 2018 |
Tools for pressing - Ball - Lock punch retainers: Part 3 type E, reduced for heavy duty |
PGD 4 |
| 18 |
IS 16793 : Part 1 : 2019 |
Tools for pressing - Ball - Lock punch retainers: Part 1 types A and B, rectangular and square for light duty |
PGD 4 |
| 19 |
IS 16793 : Part 2 : 2019 |
Tools for pressing - Ball - Lock punch retainers: Part 2 types C and D, reduced for light duty |
PGD 4 |
| 20 |
IS 1231 : 2019 |
Dimensions and Output Series of Foot Mounted Induction Motors — Frame Numbers 56 to 315 L ( Fourth Revision ) |
ETD 15 |
| 21 |
IS 1367 : Part 8 : 2020 |
Technical Supply Conditions for Threaded Steel Fasteners Part 8 Prevailing Torque Type Steel Nuts — Functional Properties ( Fifth Revision ) |
PGD 37 |
| 22 |
IS 11003 : Part 2 : 2020 |
Hydraulic Fluid Power — Mounting Dimensions for Single Rod Cylinders, 16 MPa ( 160 bar ) Series Part 2 Compact Series ( Second Revision ) |
PGD 36 |
| 23 |
IS 17445 : 2020 |
Fasteners — Preloading Test for the Detection of Hydrogen Embrittlement — Parallel Bearing Surface Method |
PGD 37 |
| 24 |
IS 5220 : 1969 |
Specification for forged horn cleats |
TED 17 |
| 25 |
IS 11132 : 1985 |
Specification for ammonia valves |
MED 17 |
