| SNo |
IS Number |
Title |
Technical Committee |
|
1 |
IS 101 : Part 5 : Sec 1 : 1988 |
Methods of sampling and test for paints, varnishes and related products: Part 5 mechanical test on paint films: Sec 1 hardness tests (Third Revision) |
CHD 20 |
|
2 |
IS 101 : Part 5 : Sec 2 : 1988 |
Methods of sampling and test for paints, varnishes and related products: Part 5 mechanical tests: Sec 2 flexibility and adhesion (Third Revision) |
CHD 20 |
|
3 |
IS 101 : Part 5 : Sec 3 : 2019 |
Methods of sampling and test for paints, varnishes and related products: Part 5 mechanical tests: Sec 3 impact resistance - falling - weight test, large - Area indenter (Fifth Revision) |
CHD 20 |
|
4 |
IS 101 : Part 6 : Sec 1 : 1988 |
Methods of sampling and test for paints, varnishes and related products: Part 6 durability tests: Sec 1 resistance to humidity under conditions of condensation (Third Revision) |
CHD 20 |
|
5 |
IS 110 : 2017 |
Ready mixed paint, brushing, grey filler, for enamels for use over primers - Specification (Third Revision) |
CHD 20 |
|
6 |
IS 149 : 1950 |
Ready mixed paint, spraying, undercoating, stoving, for enamels and general purposes colour as required |
CHD 20 |
|
7 |
IS 151 : 2017 |
Ready mixed paint, spraying, finishing, stoving, enamel for general purposes, colour as required - Specification (Second Revision) |
CHD 20 |
|
8 |
: |
|
|
|
9 |
IS 814 : 2004 |
Covered electrodes for manual metal arc welding of carbon and carbon manganese steel - Specification (Sixth Revision) |
MTD 11 |
|
10 |
IS 1079 : 2017 |
Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision) |
MTD 4 |
|
11 |
IS 1278 : 1972 |
Specification for filler rods and wires for gas welding (Second Revision) |
MTD 11 |
|
12 |
IS 1365 : 2005 |
Slotted countersunk flat head screws (Common Head Style) - product grade a (Fourth Revision) |
PGD 37 |
|
13 |
IS 1730 : 1989 |
Steel Plates, Sheets Strips and Flats for Structural and General Engineering Purposes - Dimensions (Second Revision) |
CED 7 |
|
14 |
IS 1732 : 1989 |
Steel Bars, Round and Square for Structural and General Engineering Purposes - Dimensions (Second Revision) |
CED 7 |
|
15 |
IS 1977 : 1996 |
Low Tensile Structural Steels |
MTD 4 |
|
16 |
IS 2932 : 2003 |
Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing |
CHD 20 |
|
17 |
IS 2933 : 2013 |
Enamel exterior (a) undercoating, (b) finishing |
CHD 20 |
|
18 |
IS 3618 : 1966 |
Specification for phosphate treatment of iron and steel for protection against corrosion |
MTD 24 |
|
19 |
IS 4414 : 1990 |
Wooden table tops specification (Second Revision) |
CED 35 |
|
20 |
IS 4454 : Part 1 : 2001 |
Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision) |
MTD 4 |
|
21 |
IS 4972 : 1968 |
Specification for resistance spot - Welding electrodes |
MTD 11 |
|
22 |
IS 5660 : 1970 |
Ready mixed paint, brushing, aluminium-red oxide primer |
CHD 20 |
|
23 |
IS 13871 : 1993 |
Powder coatings - Specification |
CHD 20 |
