| SNo |
IS Number |
Title |
Technical Committee |
|
1 |
IS 3168 : 1981 |
Specification for brass strip and foil for deep drawing (First Revision) |
MTD 8 |
|
2 |
IS 3400 : Part 1 : 2012 |
Methods of test for vulcanized rubber: Part 1 determination of tensile stress - Strain properties (Third Revision) |
PCD 29 |
|
3 |
IS 3400 : Part 2 : 2014 |
Methods of test for vulcanized rubber: Part 2 rubber, vulcanized or thermoplastic - Determination of hardness (Hardness Between 10 Irhd And 100 Irhd) (Fourth Revision) |
PCD 29 |
|
4 |
IS 3400 : Part 3 : 2018 |
Methods of test for vulcanized rubbers: Part 3 determination of abrasion resistance using a rotating cylindrical drum device (Second Revision) |
PCD 29 |
|
5 |
IS 3400 : Part 4 : 2012 |
Methods of test for vulcanized rubber: Part 4 accelerated ageing and heat resistance (Third Revision) |
PCD 29 |
|
6 |
IS 3400 : Part 5 : 2020 |
Methods of Test for Vulcanized Rubbers Part 5 Adhesion of Rubbers to Textile Fabrics ( Third Revision ) |
PCD 29 |
|
7 |
IS 3400 : Part 6 : 2018 |
Methods of Test for Vulcanized Rubbers Part 6 Determination of the Effect of Liquids (Fourth Revision) |
PCD 29 |
|
8 |
IS 3400 : Part 7 : 1985 |
Methods of test for vulcanized rubbers: Part 7 resistance to flex - Cracking (First Revision) |
PCD 29 |
|
9 |
IS 3400 : Part 8 : 1983 |
Methods of test for vulcanized rubbers: Part 8 resistance to crack - Growth (First Revision) |
PCD 29 |
|
10 |
IS 3400 : Part 9 : 2020 |
Methods of Test for Vulcanized Rubber Part 9 Rubber, Vulcanized or Thermoplastic — Determination of Density ( Fourth Revision ) |
PCD 29 |
|
11 |
IS 3400 : Part 10 : 1977 |
Methods of test for vulcanized rubbers: Part x compression set at constant strain (First Revision) |
PCD 29 |
|
12 |
IS 4218 : Part 1 : 2001 |
ISO general purpose metric screw threads: Part 1 basic profile - second revision) |
PGD 37 |
|
13 |
IS 4218 : Part 2 : 2001 |
ISO general purpose metric screw threads: Part 2 general plan (Second Revision) |
PGD 37 |
|
14 |
IS 4218 : Part 3 : 1999 |
ISO general purpose metric screw threads: Part 3 basic dimensions (Second Revision) |
PGD 37 |
|
15 |
IS 4218 : Part 4 : 2001 |
ISO general purpose metric screw threads: Part 4 selected sizes for screws, bolts and nuts (Second Revision) |
PGD 37 |
|
16 |
IS 4454 : Part 3 : 1975 |
Part 3 Oil hardened and tempered steel wiresalloyed |
MTD 4 |
|
17 |
IS 4454 : Part 4 : 2001 |
Steel wires for mechanical springs: Part 4 stainless steel wire (Second Revision) |
MTD 16 |
|
18 |
IS 5116 : 2020 |
Domestic and Commercial Equipment for Use with LPG — General Requirements ( Fourth Revision ) |
MED 23 |
|
19 |
IS 7608 : 1987 |
Specification for phosphor bronze wire for general engineering purposes (First Revision) |
MTD 8 |
|
20 |
IS 8119 : 1976 |
Specification for copper brazed steel tubing |
MTD 19 |
|
21 |
IS 9798 : 2013 |
Low pressure regulators for use with liquefied petroleum gas (LPG) - Specification (Second Revision) |
MED 16 |
|
22 |
IS 10773 : 1995 |
Wrought copper tubes for refrigeration and air - Conditioning purposes - Specification (First Revision) |
MTD 8 |
|
23 |
IS 319 : 2007 |
Free cutting brass bars, rods and section - Specification (Fifth Revision) |
MTD 8 |
|
24 |
: |
|
|
|
25 |
IS 554 : 1999 |
Pipe threads where pressure - Tight joints are made on the threads - Dimensions, tolerances and designation (Fourth Revision) |
PGD 37 |
|
26 |
IS 617 : 1994 |
Cast aluminium and its alloys - Ingots and castings for general engineering purposes - Specification (Third Revision) |
MTD 7 |
|
27 |
IS 742 : 1981 |
Specification for zinc base alloy die castings (Second Revision) |
MTD 9 |
|
28 |
IS 1545 : 1994 |
Solid drawn copper and copper alloy tubes for condensers and heat exchangers - Specification (Third Revision) |
MTD 8 |
|
29 |
IS 2305 : 1988 |
Method for mercurous nitrate test for copper and copper alloys (First Revision) |
MTD 8 |
|
30 |
IS 2501 : 1995 |
Solid drawn copper tubesfor general engineering purposes - Specification (Third Revision) |
MTD 8 |
|
31 |
IS 2643 : 2005 |
Pipe threads where pressure - Tight joints are not made on the threads - Dimensions, tolerances and designation (Third Revision) |
PGD 37 |
