| SNo |
IS Number |
Title |
Technical Committee |
|
1 |
IS 15914 : 2011 |
High tensile strength flat rolled steel plate (Up To 6 Mm), sheet and strip for the manufacture of welded gas cylinder - Specification |
MTD 4 |
|
2 |
IS 15894 : 2018 |
Inspection gauges for checking taper threads of gas cylinder valves and cylinder necks - Taper 1 in 16 on diameter - Specification (First Revision) |
MED 16 |
|
3 |
IS 15637 : 2006 |
Welded stainless steel cylinders for liquefied petroleum gases (LPG) from 0.5 litre to 250 litre water capacity - Specification |
MED 16 |
|
4 |
IS 13871 : 1993 |
Powder coatings - Specification |
CHD 20 |
|
5 |
IS 13258 : 2014 |
Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gas - Requirements for inspection and reconditioning of used lpg cylinders (First Revision) |
MED 16 |
|
6 |
IS 12447 : 1988 |
Specification for zinc wire for sprayed zinc coatings |
MTD 9 |
|
7 |
IS 9954 : 1981 |
Pictorial surface preparation standards for painting of steel surfaces |
CED 13 |
|
8 |
IS 9639 : 2017 |
Visual inspection of low pressure welded steel gas cylinders during manufacture - Code of practice (First Revision) |
MED 16 |
|
9 |
IS 9122 : 2008 |
Inspection gauges for checking type 2 taper thread of gas cylinder valves, taper 3 in 25 - Specification (First Revision) |
MED 16 |
|
10 |
IS 8867 : 1978 |
Saturated vapour pressure and test pressure for low pressure liquefiable gases contained in gas cylinders |
MED 16 |
|
11 |
IS 8737 : 2017 |
Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision) |
MED 16 |
|
12 |
IS 7310 : Part 1 : 2019 |
Qualification Testing of Welders - Fusion Welding Part 1 Steels (First Revision) |
MTD 11 |
|
13 |
IS 7307 : Part 1 : 1974 |
Approval tests for welding procedures: Part 1 fusion welding of steel |
MTD 11 |
|
14 |
IS 7241 : 1981 |
Glossary of terms used in gas cylinder technology (First Revision) |
MED 16 |
|
15 |
IS 7202 : 2017 |
Inspection gauges for checking type 4 (Size 1, 2, 3) taper threads of gas cylinder valves and cylinder necks - Specification (First Revision) |
MED 16 |
|
16 |
IS 7142 : 1995 |
Welded low carbon steel cylinders for low pressure liquifiable gases not exceeding 5 litre water capacity - Specification (First Revision) |
MED 16 |
|
17 |
IS 6586 : 1989 |
Metal spraying for protection of iron and steel - Recommended practice (First Revision) |
MTD 24 |
|
18 |
IS 6240 : 2008 |
Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision) |
MTD 4 |
|
19 |
IS 4853 : 1982 |
Recommended practice for radiographic inspection of fusion welded butt joints in steel pipes (First Revision) |
MTD 21 |
|
20 |
IS 4576 : 2018 |
Liquefied Petroleum Gases — Specification ( Third Revision ) |
PCD 3 |
|
21 |
IS 3657 : 2018 |
Specification for radiographic image quality indicators (Second Revision) |
MTD 21 |
|
22 |
IS 3196 : Part 3 : 2012 |
Welded low carbon steel cylinder exceeding 5 litre water capacity for low pressure liquefiable gases: Part 3 methods of test (First Revision) |
MED 16 |
|
23 |
IS 2932 : 2003 |
Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing |
CHD 20 |
|
24 |
IS 2825 : 1969 |
Code for unfired pressure vessels |
MED 1 |
|
25 |
IS 2595 : 2008 |
Industrial radiographic testing - Code of practice (Second Revision) |
MTD 21 |
|
26 |
IS 2074 : 1992 |
Ready Mixed Paint, Air Drying, Red Oxide Zinc Chrome, Priming |
CHD 20 |
|
27 |
IS 2062 : 2011 |
Hot rolled medium and high tensile structural steel - Specification (Seventh Revision) |
MTD 4 |
|
28 |
IS 1956 : Part 1 : 1976 |
Glossary of terms relating to iron and steel: Part 1 general metallurgy, heat treatment and testing (First Revision) |
MTD 22 |
|
29 |
IS 1875 : 1992 |
Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision) |
MTD 4 |
|
30 |
IS 1182 : 1983 |
Recommended - Practice for radiographic examination of fusion welded butt joints in steel plates (Second Revision) |
MTD 21 |
|
31 |
IS 1079 : 2017 |
Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision) |
MTD 4 |
|
32 |
IS 817 : 1966 |
Code of practice for training and testing of metal arc welders (Revised) |
MTD 11 |
|
33 |
IS 5 : 2007 |
Colours for ready mixed paints and enamels (Sixth Revision) |
CHD 20 |
|
34 |
IS 4683 : 1968 |
Specification for chilled iron shot and grit for use in foundries |
MTD 14 |
