| SNo |
IS Number |
Title |
Technical Committee |
| 1 |
IS 4397 : 1999 |
Cold - Rolled carbon steel strips for ball and roller bearing cages retainers - Specification (Second Revision) |
MTD 4 |
| 2 |
IS 5522 : 2014 |
Stainless steel sheets and strips for utensils - Specification (Third Revision) |
MTD 16 |
| 3 |
IS 3642 : Part 1 : 1990 |
Surgical instruments - Specification: Part 1 non - Cutting, articulated instruments (Second Revision) |
MHD 1 |
| 4 |
IS 12841 : Part 2 : 1989 |
Surgical Instruments - Needle Holders - Part 2 : With Carbide Inserts, Stratte's Pattern |
MHD 1 |
| 5 |
IS 11318 : 1985 |
Bronchoscope, Aspirating, Negus' Pattern |
MHD 4 |
| 6 |
IS 11319 : 1985 |
Oesophagoscope, Negus' Pattern |
MHD 4 |
| 7 |
IS 12901 : 1990 |
ENT surgery instruments - Laryngeal fine grasping forceps, crocodile jaws, straight - Specification |
MHD 4 |
| 8 |
IS 12507 : 1988 |
General requirements for dental pliers |
MHD 8 |
| 9 |
IS 3075 : Part 1 : 1986 |
Specification for circlips: Part 1 for shafts (First Revision) |
PGD 35 |
| 10 |
IS 3075 : Part 2 : 1986 |
Specification for circlips: Part 2 for bores (First Revision) |
PGD 35 |
| 11 |
IS 3075 : Part 3 : 1986 |
Specification for circlips: Part 3 type e for shafts (First Revision) |
PGD 35 |
| 12 |
IS 6171 : 1992 |
Screwing taps - Technical supply conditions (Second Revision) |
PGD 32 |
| 13 |
IS 6436 : 1989 |
Thoracic Surgery Instruments - Rib Spreader, Finochietto's Pattern, Adult Size |
MHD 6 |
| 14 |
IS 6777 : 1989 |
Thoracic and cardiovascular surgery instruments - Forceps, dissecting, lung - Specification (First Revision) |
MHD 6 |
| 15 |
IS 7367 : 1987 |
Clamps, Coarctation, Potts' Pattern, Straight and Angular |
MHD 6 |
| 16 |
IS 7399 : 1987 |
Knife, Sternum, Lebsche's Pattern |
MHD 6 |
| 17 |
IS 7971 : 1987 |
Tourniquet, Cardiovascular Rumel-Belmont's Pattern |
MHD 6 |
| 18 |
IS 8409 : 1991 |
Cardiovascular Surgery Instruments - Dilator, Valve, Tubb's Mitral Pattern |
MHD 6 |
| 19 |
IS 1931 : 2000 |
ENGINEER’S FILES — SPECIFICATION ( Third Revision) |
PGD 34 |
| 20 |
IS 14207 : 1994 |
Household sewing machines - Open type shuttle race sub - Assembly - Specification |
MED 29 |
| 21 |
IS 13806 : 1993 |
Household sewing machine - Closed type shuttle race assembly - Specification |
MED 29 |
| 22 |
IS 11347 : 1995 |
Household sewing machtnes - Shuttle driver - Specification (First Revision) |
MED 29 |
| 23 |
IS 4341 : 1997 |
Household sewing machines - Feed bar rollers and studs - Specification (First Revision) |
MED 29 |
| 24 |
IS 4339 : 1997 |
Household sewing machines - Needle bar link studs - Specification (First Revision) |
MED 29 |
| 25 |
IS 4338 : 1991 |
Household sewing machines vertical oscillating shuttle - Specification f second revision) |
MED 29 |
| 26 |
IS 3817 : 1991 |
Household sewing machines - Arm shaft - Specification (First Revision) |
MED 29 |
| 27 |
IS 3375 : 1991 |
Household sewing machines - Bobbin case - Specification (Second Revision) |
MED 29 |
| 28 |
IS 13561 : 1992 |
Textile machinery and accessories – Ear-shaped nylon travellers for ring doubling and twisting – Specification |
TXD 14 |
| 29 |
IS 14676 : 1999 |
Spinning rings used in CHARKHAS – Specification |
TXD 14 |
| 30 |
IS 15379 : 2003 |
Textile machinery and accessories - Steel pins for spinning preparatory and spinning machinery |
TXD 14 |
| 31 |
IS 1586 : 2000 |
Method for Rockwell Hardness Test for Metallic Material (Scales A-B-C-D-E-F-G-H-K 15N, 30N, 45N, 15T, 30T and 45T) |
MTD 3 |
| 32 |
IS 13360 : Part 5 : Sec 22 : 2017 |
Plastics - Methods of testing: Part 5 mechanical properties section 22 determination of resistance to wear by abrasive wheels (First Revision) |
PCD 27 |
| 33 |
IS 13360 : Part 4 : Sec 1 : 2000 |
Plastics - Methods of testing: Part 4 rheological properties section 1 determination of the melt mass - Flow rate (Mfj3)And the melt volume - Flow rate (Mvr) of thermoplastics (First Revision) |
PCD 27 |
| 34 |
IS 3063 : 1994 |
Fasteners - Single coil rectangular section spring lock washers specification (Second Revision) |
PGD 37 |
| 35 |
IS B14769 : 2000 |
Household Sewing Machine Head - General Requirements (Bilingual) |
MED 29 |
| 36 |
IS 3888 : 1987 |
Specification for spatula, stainless steel, dental (First Revision) |
MHD 8 |
| 37 |
IS 3890 : Part 1 : 1986 |
Specification for instruments, plastic filling, dental: Part 1 designation numbers 1, 3, 4, 5 and 6 (First Revision) |
MHD 8 |
| 38 |
IS 4316 : 1991 |
Orthodontic pliers, snipe nose - Shape,dimensions and tests (First Revision) |
MHD 8 |
| 39 |
IS 4319 : Part 2 : 1986 |
Specification for pliers, stretching and contouring, dental: Part 2 pliers, contouring (First Revision) |
MHD 8 |
| 40 |
IS 4975 : 1986 |
Specification for elevators, dental, No. 1, 2 and 3 (First Revision) |
MHD 8 |
| 41 |
IS 4976 : 1987 |
Specification for forceps extraction, dental, upper anteriors, No. 1 and 2 (First Revision) |
MHD 8 |
| 42 |
IS 5179 : 1986 |
Specification for pluggers, root canal, dental, No. PLG 1, 2 and 3 (First Revision) |
MHD 8 |
| 43 |
IS 5582 : 1986 |
Specification for mandrels, dental, No. 1, 2 and 3 (First Revision) |
MHD 8 |
| 44 |
IS 5794 : 1986 |
Specification - For pliers, pin - Roughening and bending, dental (First Revision) |
MHD 8 |
| 45 |
IS 5795 : 1991 |
Orthodontic pliers, Crown and ligating, Howe's pattern - Shape, dimensions and tests |
MHD 8 |
| 46 |
IS 6402 : 1986 |
Specification for forceps, rubber dam clamp and cotton roll clamp, dental (First Revision) |
MHD 8 |
| 47 |
IS 6829 : 1991 |
Dental instruments - Orthodontic pliers, angle wire bending - Shape, dimensions and tests (First Revision) |
MHD 8 |
| 48 |
IS 6866 : 1986 |
Specification for forceps, extraction, dental, upper wisdom tooth (First Revision) |
MHD 8 |
| 49 |
IS 6868 : 1991 |
Dental instruments - Dental extraction forceps - Specification (First Revision) |
MHD 8 |
| 50 |
IS 6870 : 1986 |
Specification for pliers, loop bending, dental (First Revision) |
MHD 8 |
| 51 |
IS 7474 : 1986 |
Specification for pliers, collar, dental (First Revision) |
MHD 8 |
| 52 |
IS 1959 : 1994 |
Silver anodes for electroplating - Specification (Second Revision) |
MTD 24 |
| 53 |
IS 8287 : 1986 |
Specification for pliers, band stretching and contouring, parrot beak, dental (First Revision) |
MHD 8 |
| 54 |
IS 5905 : 1989 |
Sprayed aluminium and zinc coatings on iron and steel - Specification (First Revision) |
MTD 24 |
| 55 |
IS 12714 : 1989 |
Bimetallic tape for electrical contacts - Specification |
MTD 10 |
| 56 |
IS 8365 : 1991 |
Copper alloys for spot and seam resistance welding electrodes (First Revision) |
MTD 8 |
| 57 |
IS 1545 : 1994 |
Solid drawn copper and copper alloy tubes for condensers and heat exchangers - Specification (Third Revision) |
MTD 8 |
| 58 |
IS 2949 : 1992 |
Engineering metrology - Plain V - Blocks for inspection purposes - Specification (Second Revision) |
PGD 25 |
| 59 |
IS 3179 : 1990 |
Engineering metrology - Feeler gauges (second revision) |
PGD 25 |
| 60 |
IS 4211 : 1993 |
Gauges - Thread pitch gauges for ISO metric screw threads (Pitch Range 0.4 To 6 Mm) - Specification (First Revision) |
PGD 25 |
| 61 |
IS 4440 : 1996 |
Engineering metrology - Precision equipment - Slip gauge accessories (First Revision) |
PGD 25 |
| 62 |
IS 9475 : 1986 |
Specification for plug and ring gauges for self release 7/24 tapers (First Revision) |
PGD 25 |
| 63 |
IS 12836 : 1989 |
36 - Nickel iron soft magnetic rods - Specification |
MTD 16 |
| 64 |
IS 12881 : 1990 |
36 - Nickel iron soft magnetic strips - Specification |
MTD 16 |
| 65 |
IS 12882 : 1990 |
48 - Nickel iron soft magnetic strip - Specification |
MTD 16 |
| 66 |
IS 6911 : 2017 |
Stainless steel plate, sheet and strip - Specification (Second Revision) |
MTD 16 |
| 67 |
IS 6779 : 1989 |
Thoracic Surgery Instruments - Forceps, Dissecting and Ligature, Mixter's Pattern - Specification (First Revision) |
MHD 6 |
| 68 |
IS 1367 : Part 3 : 2017 |
Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision) |
PGD 37 |
| 69 |
IS 16772 : 2018 |
Round steel short link chains for lifting purposes - Fine tolerance hoist chains for hand operated chain hoists - Grade vh |
MED 14 |
| 70 |
IS 16773 : 2018 |
Round steel short link chains for lifting purposes - Fine tolerance hoist chains for hand operated chain hoists - Grade th |
MED 14 |
| 71 |
IS 7178 : 2018 |
Heat - Treated steel tapping screws - Mechanical properties (Fourth Revision) |
PGD 37 |
| 72 |
IS 15703 : 2018 |
Sintered metal materials, excluding hardmetals - Determination of apparent hardness and microhardness (First Revision) |
MTD 25 |
| 73 |
IS 4488 : 2018 |
Forceps, Tonsil Holding (Muck's and White's Patterns) Specification ( First Revision ) |
MHD 4 |
| 74 |
IS 1610 : 2018 |
Household sewing machines - General requirements (Fourth Revision) |
MED 29 |
| 75 |
IS 5664 : 2019 |
Lubricating connectors - Specification (Second Revision) |
PGD 19 |
| 76 |
IS 17149 : Part 2 : 2019 |
Metallic materials - Leeb hardness test: Part 2 verification and calibration of the testing devices |
MTD 3 |
| 77 |
IS 10651 : 2019 |
Hub axle, front for moped - Specification (First Revision) |
TED 2 |
| 78 |
IS 10652 : 2019 |
Pedal assembly for moped - Specification (First Revision) |
TED 2 |
| 79 |
IS 10653 : 2019 |
Hub axle, rear, for moped - Specification (First Revision) |
TED 2 |
| 80 |
IS 17166 : 2019 |
Technical product documentation -- Heat-treated ferrous parts -- Presentation and indications |
PGD 24 |
| 81 |
IS 3758 : 2018 |
Hooks, aural - Specification (First Revision) |
MHD 4 |
| 82 |
IS 3799 : 2019 |
Forceps, aural and nasal, crocodile action - Specification (First Revision) |
MHD 4 |
| 83 |
IS 4489 : 2018 |
Forceps, Nasal Turbinate, Luc’s — Specification ( First Revision ) |
MHD 4 |
| 84 |
IS 4514 : 2018 |
Forceps, Tonsil Dissecting (Waugh's Pattern) - Specification ( First Revision ) |
MHD 4 |
| 85 |
IS 4520 : 2018 |
Forceps, Punch, Nasal Citelli's Antrum and Hajek's Sphenoidal— Specification (First Revision) |
MHD 4 |
| 86 |
IS 4504 : 2018 |
Forceps, peritonsillar - Specification (First Revision) |
MHD 4 |
| 87 |
IS 1367 : Part 5 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 5 mechanical properties of fasteners made of carbon steel and alloy steel - Set screws and similar threaded fasteners with specified hardness classes - Coarse thread and fine pitch thread (Fourth Revision) |
PGD 37 |
| 88 |
IS 1367 : Part 14 : Sec 3 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 14 mechanical properties of corrosion - Resistant stainless steel fasteners section 3 set screws and similar fasteners not under tensile stress (Fourth Revision |
PGD 37 |
| 89 |
IS 1448 : Part 149 : 2020 |
Methods of Test for Petroleum and its Products Part 149 Diesel Fuel - Assessment of Lubricity Using the High - Frequency Reciprocating Rig ( HFRR ) - Test Method ( Second Revision ) |
PCD 1 |
| 90 |
IS 1501 : Part 2 : 2020 |
Metallic Materials — Vickers Hardness Test Part 2 Verification and Calibration of Testing Machines ( Fifth Revision ) |
MTD 3 |
| 91 |
IS 1501 : Part 3 : 2020 |
Metallic Materials — Vickers Hardness Test Part 3 Calibration of Reference Blocks ( Fifth Revision ) |
MTD 3 |
| 92 |
IS 1501 : Part 4 : 2020 |
Metallic Materials — Vickers Hardness Test Part 4 Tables of Hardness Values ( Fifth Revision ) |
MTD 3 |
| 93 |
IS 513 : Part 1 : 2016 |
Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision) |
MTD 4 |
| 94 |
IS 513 : Part 2 : 2016 |
Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision) |
MTD 4 |
| 95 |
IS 4217 : 2020 |
Rolling bearings -- Needle rollers -- Specification (Second Revision) |
PGD 13 |
| 96 |
IS 9202 : 2020 |
Rolling Bearings — Cylindrical Rollers — Specification ( First Revision ) |
PGD 13 |
| 97 |
IS 3760 : 1966 |
Probe, Aural, Jobson Horne's Pattern |
MHD 4 |
| 98 |
IS 963 : 1958 |
Specification for chrome molybdenum steel bars and rods for aircraft purposes |
MTD 16 |
| 99 |
IS 9295 : 1983 |
Specification for steel tubes for idlers for belt conveyors (First Revision) |
MTD 19 |
| 100 |
IS 15045 : Part 2 : 2021 |
Pneumatic Fluid Power - Five-Port Directional Control Valves Part 2 Mounting Interface Surfaces with Optional Electrical Connector ( First Revision ) |
PGD 36 |
| 101 |
IS 1500 : Part 2 : 2013 |
Matallic Materials - Brinell Hardness Test Part 2 Verification and Calibration Testing Machines |
MTD 3 |
| 102 |
IS 5402 : Part 1 : 2021 |
Microbiology of the food chain - Horizontal method for the enumeration of microorganisms- Part 1: Colony count at 30 C by the pour plate technique |
FAD 31 |
| 103 |
IS 16143 : Part 8 : 2021 |
Hard coal and coke - Mechanical sampling : Part 8 methods of testing for bias (First Revision) |
PCD 7 |
| 104 |
IS 17582 : 2021 |
Specification for Infantometer |
PGD 26 |
| 105 |
IS 6416 : 1988 |
Methods for measuring case depth of steel (First Revision) |
MTD 22 |
| 106 |
IS 11169 : Part 1 : 1984 |
Specification for steels for cold heading/cold extrusion applications: Part 1 wrought carbon and low alloy steels |
MTD 16 |
| 107 |
IS 13360 : Part 4 : Sec 5 : 2000 |
Plastics - Methods of testing: Part 4 rheological properties section 5 determination of the fluidity of plastics using capillary and slit - Die rheometers |
PCD 27 |
| 108 |
IS/IEC 61071 : 2017 |
CAPACITORS FOR POWER ELECTRONICS (First Revision) |
ETD 29 |
| 109 |
IS 1367 : Part 14 : Sec 1 : 2018 |
Technical supply conditions for threaded steel fasteners: Part 14 mechanical properties of corrosion - Resistant stainless - Steel fasteners section 1 bolts, screws and studs (Fourth Revision) |
PGD 37 |
| 110 |
IS 1367 : Part 14 : Sec 2 : 2018 |
Technical Supply Conditions for Threaded Steel Fasteners Part 14 Mechanical Properties of Corrosion-resistant Stainless steel Fasteners Section 2 Nuts (Fourth Revision) |
PGD 37 |
| 111 |
IS 6369 : 1971 |
Specification for fleshing knife for leather industry |
CHD 17 |
| 112 |
IS 4239 : 1970 |
Specification for mechanical bevel protractors (First Revision) |
PGD 25 |
| 113 |
IS 3078 : 1989 |
Rings for spinning and doubling frames – Specification (fourth revision) |
TXD 14 |
| 114 |
IS 5988 : 1970 |
Specification for spring dowel sleeves (Light And Heavy Patterns) for use in foundries |
MTD 14 |
| 115 |
IS 9294 : 1979 |
Cold-Rolled Stainless Steel Strips for Razor Blades |
MTD 16 |
| 116 |
IS 17631 : 2022 |
Work Chairs - Specification |
CED 35 |
| 117 |
IS 3825 : 1990 |
Inset mail wire healds for jute weaving – Specification (second revision) |
TXD 14 |
| 118 |
IS 4909 : 1990 |
Card and gill pins for use in jute industry – Specification (first revision) |
TXD 14 |
| 119 |
IS 6268 : 1971 |
Specification for accessories for use in shuttles for plain calico looms |
TXD 14 |
| 120 |
IS 11536 : 2022 |
Processed Cereal Based Complementary Foods ? Specification ( Third Revision ) |
FAD 24 |
| 121 |
IS 10174 : 1982 |
Tongs, skull Traction, Crutchfield's Pattern |
MHD 7 |
| 122 |
IS 11084 : 1984 |
Specification for silver palladium alloy wire and strip for electrical contacts |
MTD 10 |
| 123 |
IS 6396 : 2000 |
Methods of measuring decarbunzed depth of steel (Second Revision) |
MTD 22 |
| 124 |
IS 9139 : 1979 |
Specification for malleable iron shots and grits for use in foundries |
MTD 14 |
| 125 |
IS/IEC 60372 : 1984 |
Locking devices for ball and socket couplings of string insulators units - Dimensions and tests |
ETD 6 |
| 126 |
IS 17885 : Part 1 : 2022 |
Automation systems and integration Digital twin framework for manufacturing Part 1: Overview and general principles |
PGD 18 |
| 127 |
IS 2744 : 2022 |
1-Naphthylamine (Second Revision) |
PCD 26 |
| 128 |
IS 10795 : 1984 |
Specification for accessories for use in shuttles for pirn-changing automatic cotton looms |
TXD 14 |
| 129 |
IS 10725 : 1983 |
Specification for knife, myringotomy |
MHD 4 |
| 130 |
IS 10726 : 1983 |
Specification for knife, meatal skin incision |
MHD 4 |
| 131 |
IS 181 : 2022 |
Textiles – Leopard Cloth – Specification (third revision) |
TXD 31 |
| 132 |
IS 181 : 2022 |
Textiles – Leopard Cloth – Specification (third revision) |
TXD 31 |
| 133 |
IS 3168 : 1981 |
Specification for brass strip and foil for deep drawing (First Revision) |
MTD 8 |
| 134 |
IS 17018 : Part 1 : 2022 |
Solar Photovoltaic Water Pumping Systems Part 1 Centrifugal Pumps Specification |
MED 20 |
| 135 |
IS 802 : Part 6 : 2022 |
Use of Structural Steel in Overhead Transmission Line Towers — Code of Practice Part 6 Tower Erection |
CED 7 |
| 136 |
IS 2079 : 2022 |
GRAPHITE FOR PENCIL SLIPS - SPECIFICATION (Second Revision) |
CHD 14 |
| 137 |
IS 6053 : Part 2 : 1971 |
Specification for hand tools for footwear industry: Part 2 bottom cutting knife (Rampi) |
CHD 19 |
| 138 |
IS 6053 : Part 3 : 1971 |
Handtools for footwear industry: Part 3 Designers' knife |
CHD 19 |
| 139 |
IS 3848 : 1981 |
Method for end quench test for hardenability of steel (First Revision) |
MTD 22 |
| 140 |
IS 6603 : 2001 |
Stainless steel bars and flats - Specification (First Revision) |
MTD 16 |
| 141 |
IS 2151 : 2022 |
Maize Germ Oilcake as Livestock Feed Ingredient � Specification |
FAD 5 |
| 142 |
IS 13902 : Part 1 : 2022 |
SOCKETS FOR WIRE ROPES FOR GENERAL PURPOSES PART 1 GENERAL CHARACTERISTICS AND CONDITIONS OF ACCEPTANCE First Revision |
MED 10 |
| 143 |
IS 19000 : 2022 |
Online Consumer Reviews Principles and Requirements for their Collection Moderation and Publication |
SSD 9 |
| 144 |
IS 2095 : Part 3 : 2022 |
Gypsum Plaster Boards — Specification Part 3 Reinforced Gypsum Plaster Boards and Ceiling Tiles ( Fourth Revision ) |
CED 4 |
| 145 |
IS 6053 : Part 1 : 1970 |
Specification for hand tools for footwear industry: Part 1 upper clicking knife |
CHD 19 |
| 146 |
IS 3092 : 1982 |
Specification for Rubber Draining and Tapping Knife (First Revision) |
FAD 11 |
| 147 |
IS 7346 : 1987 |
Raspatories, Rib, Semb's Pattern |
MHD 6 |
| 148 |
IS 7382 : 1987 |
Shears, Rib, Price Thomas' Pattern |
MHD 6 |
| 149 |
IS 10938 : 1984 |
Specification for searcher, double edged with handle and sheath |
MHD 13 |
| 150 |
IS 10955 : 1984 |
Specification for gimlet for trephine |
MHD 13 |
| 151 |
IS 11566 : 1986 |
Specification for valve retractors |
MHD 6 |
| 152 |
IS 5005 : 1968 |
Specification for burnisher, dental, No. BRN 1/2 |
MHD 8 |
| 153 |
IS 5017 : 1968 |
Specification for carvers, dental, No. CAR 1/2, 314 and 5/6 |
MHD 8 |
| 154 |
IS 7379 : 1987 |
Clamps, Patent Ductus, Potts' Pattern, Straight and Angular |
MHD 6 |
| 155 |
IS 7972 : 1987 |
Scissors, Dissecting, Metzenbaum's Pattern |
MHD 6 |
| 156 |
IS 15326 : Part 4 : 2022 |
Quality requirements for fusion welding of metallic materials: Part 4 elementary quality requirements Second Revision |
MTD 11 |
| 157 |
IS 6395 : 1989 |
Thoracic Surgery Instruments - Clamps, Auricle, Crafoord's Pattern |
MHD 6 |
| 158 |
IS 6442 : 1989 |
Thoracic Surgery Instruments - Shears, Rib, Tudor Edward's Pattern for Posterior End of Ribs - Specification(First Revision) |
MHD 6 |
| 159 |
IS 6466 : 1989 |
Thoracic and cardiovascular surgery instruments - Needle holders - Specification (First Revision) |
MHD 6 |
| 160 |
IS 6467 : 1989 |
Thoracic Surgery Instruments - Periosteotome, Rib, Alexander's Pattern |
MHD 6 |
| 161 |
IS 6468 : 1989 |
Thoracic Surgery Instruments - Trocar, Empyema, Nelson's Pattern |
MHD 6 |
| 162 |
IS 6778 : 1989 |
Thoracic Surgery Instruments - Forceps, Lung, Duval's Pattern |
MHD 6 |
| 163 |
IS 6780 : 1989 |
Thoracic Surgery Instruments - Forceps, Artery, Robert's Pattern, Curved on Flat |
MHD 6 |
| 164 |
IS 7355 : 1987 |
Spreader, Rib, Tuffier's Pattern, Adult Size |
MHD 6 |
| 165 |
IS 7434 : 1987 |
Retractor, Scapula, Tudor Edward's Pattern |
MHD 6 |
| 166 |
IS 8549 : 1991 |
Cardiovascular surgery instruments - Angled scissors, potts smith pattern - Specification (First Revision) |
MHD 6 |
| 167 |
IS 10953 : 1984 |
Specification for catheter uterine, single channel (Nelson Type) |
MHD 13 |
| 168 |
IS 1296 : 1989 |
Household sewing machine - Presser foot - Specification (Third Revision) |
MED 29 |
| 169 |
IS 9408 : 1986 |
Specification for retractor, self retaining (First Revision) |
MHD 7 |
| 170 |
IS 10765 : 1983 |
Forceps, Dissecting, Toothed and Bayonet Shaped, Cushing's Pattern |
MHD 7 |
