| SNo |
IS Number |
Title |
Technical Committee |
|
1 |
IS 456 : 2000 |
Plain and reinforced concrete - Code of practice (Fourth Revision) |
CED 2 |
|
2 |
IS 800 : 2007 |
General construction in steel - Code of practice (Third Revision) |
CED 7 |
|
3 |
IS 875 : Part 1 : 1987 |
Code of practice for design loads (Other Than Earthquake) for buildings and structures: Part 1 dead loads - Unit weights of building materials and stored materials (Second Revision) |
CED 37 |
|
4 |
IS 1079 : 2017 |
Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision) |
MTD 4 |
|
5 |
IS 1161 : 2014 |
Steel tubes for structural purposes - Specification (Fifth Revision) |
MTD 19 |
|
6 |
IS 1905 : 1987 |
Code of practice for structural use of unreinforced masonry (Third Revision) |
CED 13 |
|
7 |
IS 2062 : 2011 |
Hot rolled medium and high tensile structural steel - Specification (Seventh Revision) |
MTD 4 |
|
8 |
IS 2379 : 1990 |
Pipelines - Identification - Colour code (First Revision) |
MED 17 |
|
9 |
IS 2508 : 2016 |
Polyethylene films and sheets - Specification (Third Revision) |
PCD 12 |
|
10 |
IS 3370 : Part 1 : 2021 |
Concrete Structures for Retaining Aqueous Liquids - Code of Practice : Part 1 General Requirements (Second Revision) |
CED 2 |
|
11 |
IS 3370 : Part 2 : 2021 |
Concrete Structures for Retaining Aqueous Liquids - Code of Practice : Part 2 Plain and Reinforced Concrete (Second Revision) |
CED 2 |
|
12 |
IS 4923 : 2017 |
Hollow steel sections for structural use - Specification (Third Revision) |
MTD 19 |
|
13 |
IS 4984 : 2016 |
Polyethylene Pipes for Water Supply - Specification (Fifth Revision) |
CED 50 |
|
14 |
IS 5312 : Part 1 : 2004 |
Swing check type reflux (non-return) valves for water works purposes - Specification: Part 1 Single door pattern (second revision) |
CED 3 |
|
15 |
IS 5312 : Part 2 : 2013 |
Swing Check Type Reflux (Non-Return) Valves for Water Works Purpose - Specification Part 2 : Multi-Door Pattern |
CED 3 |
|
16 |
IS 5572 : 2009 |
Classification of hazardous areas (Other Than Mines) having flammable gases and vapours for electrical installation (Third Revision) |
ETD 22 |
|
17 |
IS 6092 : Part 1 : 1985 |
Methods of sampling and test for fertilizers: Part 1 sampling (First Revision) |
FAD 7 |
|
18 |
IS 6092 : Part 2 : Sec 1 : 2004 |
Methods of sampling and test for fertilizers: Part 2 determination of nitrogen: Sec 1 introduction (Second Revision) |
FAD 7 |
|
19 |
IS 6092 : Part 2 : Sec 2 : 2004 |
Methods of sampling and test for fertilizers: Part 2 determination of nitrogen: Sec 2 test methods not covered under dual number standards (Second Revision) |
FAD 7 |
|
20 |
IS 6092 : Part 2 : Sec 3 : 2004 |
Methods of sampling and test for fertilizers: Part 2 determination of nitrogen: Sec 3 nitrate nitrogen content - Nitron gravimetric method |
FAD 7 |
|
21 |
IS 6092 : Part 2 : Sec 4 : 2004 |
Methods of sampling and test for fertilizers: Part 2 determination of nitrogen: Sec 4 ammoniacal nitrogen content - Titrimetric method after distillation |
FAD 7 |
|
22 |
IS 6092 : Part 2 : Sec 5 : 2004 |
Methods of sampling and test for fertilizers: Part 2 determination of nitrogen: Sec 5 total nitrogen content - Titrimetric method after distillation |
FAD 7 |
|
23 |
IS 6092 : Part 3 : Sec 1 : 2004 |
Methods of sampling and test for fertilizers: Part 3 determination of phosphorus: Sec 1 introduction (Second Revision) |
FAD 7 |
|
24 |
IS 6092 : Part 3 : Sec 2 : 2004 |
Methods of sampling and test for fertilizers: Part 3 determination of phosphorus: Sec 2 test methods not covered under dual number standards (Second Revision) |
FAD 7 |
|
25 |
IS 6092 : Part 3 : Sec 3 : 2004 |
Methods of sampling and test for fertilizers: Part 3 determination of phosphorus: Sec 3 extraction of water - Soluble phosphates |
FAD 7 |
|
26 |
IS 6092 : Part 3 : Sec 4 : 2004 |
Methods of sampling and test for fertilizers: Part 3 determination of phosphorus: Sec 4 quinoline phosphomolybdate gravimetric method |
FAD 7 |
|
27 |
IS 6092 : Part 3 : Sec 5 : 2004 |
Methods of sampling and test for fertilizers: Part 3 determination of phosphorus: Sec 5 extraction of phosphates soluble in mineral acids |
FAD 7 |
|
28 |
IS 6092 : Part 4 : 1985 |
Methods of sampling and test for fertilizers: Part 4 determination of potassium (First Revision) |
FAD 7 |
|
29 |
IS 6092 : Part 5 : 1985 |
Methods of sampling and test for fertilizers: Part 5 determination of secondary elements and micronutrients (First Revision) |
FAD 7 |
|
30 |
IS 6092 : Part 6 : 1985 |
Methods of sampling and test for fertilizers: Part 6 determination of moisture and impurities (First Revision) |
FAD 7 |
|
31 |
IS 6940 : 1982 |
Methods of test for pesticides and their formulations (First Revision) |
FAD 1 |
|
32 |
IS 7016 : Part 1 : Sec 1 : 2022 |
Methods of Test for Rubber or Plastics Coated Fabrics Part 1 Determination of Roll Characteristics Section 1 Methods for Determination of Length, Width and Net Mass ( Third Revision ) |
TXD 33 |
|
33 |
IS 7016 : Part 1 : Sec 2 : 2019 |
Methods of Test for Coated and Treated Fabrics: Part 1 Determination of Roll Characteristics Section 2 Methods for Determination of Total Mass Per Unit Area, Mass Per Unit Area of Coating and Mass Per Unit Area of Substrate (Second Revision) |
TXD 33 |
|
34 |
IS 7016 : Part 1 : Sec 3 : 2019 |
Methods of Test for Coated and Treated Fabrics: Part 1 Determination of Roll Characteristics Section 3 Method for Determination of Thickness (Second Revision) |
TXD 33 |
|
35 |
IS 7016 : Part 2 : 2022 |
Methods of Test for Rubber or Plastics Coated Fabrics Part 2 Determination of Tensile Strength and Elongation at Break ( Third Revision ) |
TXD 33 |
|
36 |
IS 7016 : Part 3 : Sec 1 : 2022 |
Methods of Test for Rubber or Plastics Coated Fabrics Part 3 Determination of Tear Resistance Section 1 Constant Rate of Tear Methods (Third Revision) |
TXD 33 |
|
37 |
IS 7016 : Part 3 : Sec 2 : 2017 |
Methods of test for coated and treated fabrics: Part 3 determination of tear resistance section 2 ballistic pendulum method (Second Revision) |
PCD 29 |
|
38 |
IS 7016 : Part 4 : 2003 |
Methods of Test for Coated and Treated Fabrics: Part 4 Rubber - or Plastics - Coated Fabrics - Determination of Resistance to Damage by Flexing (Second Revision) |
TXD 33 |
|
39 |
IS 7016 : Part 5 : 2019 |
Methods of Test for Coated and Treated Fabrics: Part 5 Rubber - or Plastics - Coated Fabrics - Determination of Coating Adhesion (Third Revision) |
TXD 33 |
|
40 |
IS 7016 : Part 6 : Sec 1 : 2016 |
Methods of test for coated and treated fabrics: Part 6 determination of bursting strength section 1 steel - Ball method (Second Revision) |
PCD 29 |
|
41 |
IS 7016 : Part 6 : Sec 2 : 2022 |
METHODS OF TEST FOR RUBBER OR PLASTICS COATED FABRICS PART 6 DETERMINATION OF BURSTING STRENGTH SECTION 2 HYDRAULIC METHOD ( Third Revision ) |
TXD 33 |
|
42 |
IS 7016 : Part 7 : 2009 |
Methods of test for coated and treated fabrics: Part 7 rubber - Or plastics - Coated fabrics - Determination of resistance to penetration by water (Second Revision) |
TXD 33 |
|
43 |
IS 7016 : Part 8 : 1975 |
Methods of test for coated and treated fabrics: Part 8 accelerated ageing |
PCD 29 |
|
44 |
IS 7016 : Part 9 : 2003 |
Methods of Test for Coated and Treated Fabrics: Part 9 Rubber - or Plastics - Coated Fabrics - Determination of Blocking Resistance (Second Revision) |
TXD 33 |
|
45 |
IS 7016 : Part 10 : 2022 |
Methods of Test for Rubber or Plastics Coated Fabrics Part 10 Low-Temperature Bend Test ( Second Revision ) |
TXD 33 |
|
46 |
IS 7016 : Part 11 : 1987 |
Methods of test for coated and treated fabrics: Part 11 determination of flexibility - Flat loop method |
PCD 29 |
|
47 |
IS 7016 : Part 12 : 1987 |
Methods of Test for Coated and Treated Fabrics Part 12 Determination of Tack-Tear Resistance |
TXD 33 |
|
48 |
IS 7016 : Part 13 : 2003 |
Methods of Test for Coated and Treated Fabrics: Part 13 Rubber - or Plastics-Coated Fabrics - Determination of Crush Resistance (First Revision) |
TXD 33 |
|
49 |
IS 7016 : Part 14 : 2003 |
Methods of test for coated and treated fabrics: Part 14 rubber - Or plastics - Coated fabrics - Low temperature impact test (First Revision) |
TXD 33 |
|
50 |
IS 7016 : Part 15 : 2019 |
Methods of Test for Coated and Treated Fabrics Part 15 Determination of Abrasion Resistance Using Taber Abrader |
TXD 33 |
|
51 |
IS 8329 : 2000 |
Centrifugally cast (Spun) ductile iron pressure pipes for water, gas and sewage - Specification (Third Revision) |
MTD 6 |
|
52 |
IS 8749 : 2002 |
Biogas stove - Specification (Second Revision) |
MED 23 |
|
53 |
IS 8935 : 1985 |
Specification for electric solenoid operated actuators (First Revision) |
ETD 18 |
|
54 |
IS 9334 : 1986 |
Specification for electric motor operated actuators (First Revision) |
ETD 18 |
|
55 |
IS 9523 : 2000 |
Ductile iron fittings for pressure pipes for water, gas and sewage - Specification (First Revision) |
MTD 6 |
|
56 |
IS 9890 : 1981 |
Specification for general purpose ball valves |
MED 17 |
|
57 |
IS/ISO 10434 : 2020 |
STEEL GATE VALVES FLANGED AND BUTT-WELDED ENDS FOR PETROLEUM PETROCHEMICALS AND ALLIED INDUSTRIES |
MED 17 |
|
58 |
IS 12701 : 1996 |
Rotational moulded polyethylene water storage tanks - specification (First Revision) |
CED 3 |
|
59 |
IS 12866 : 2021 |
Plastic Translucent Sheets made from Thermo-Setting Polyester Resin Glassfibre Reinforced - Specification |
CED 5 |
|
60 |
IS 12986 : Part 1 : 1990 |
Biogas plants - Glass fibre reinforced polyester resin gas holders - Specification: Part 1 with steel frame |
MED 4 |
|
61 |
IS 13095 : 2020 |
Butterfly Valves for General Purposes ( First Revision ) |
MED 17 |
|
62 |
IS 13349 : 1992 |
Cast iron single faced thimble mounted sluice gates - Specification |
CED 3 |
|
63 |
IS 14333 : 2022 |
Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent - Specification (First Revision) |
CED 50 |
|
64 |
IS 15045 : Part 1 : 2021 |
Pneumatic Fluid Power - Five-Port Directional Control Valves Part 1 Mounting Interface Surfaces without Electrical Connector ( First Revision ) |
PGD 36 |
|
65 |
IS 15045 : Part 2 : 2021 |
Pneumatic Fluid Power - Five-Port Directional Control Valves Part 2 Mounting Interface Surfaces with Optional Electrical Connector ( First Revision ) |
PGD 36 |
|
66 |
IS 15045 : Part 3 : 2001 |
Pneumatic fluid power - Five port directional control valves: Part 3 code system for communication of valve functions |
PGD 36 |
|
67 |
IS 15663 : Part 1 : 2006 |
Design and installation of natural gas pipelines - Code of Practice : Part 1 Laying of pipelines |
CED 7 |
|
68 |
IS 15778 : 2007 |
Chlorinated Polyvinyl Chloride (CPVC) Pipes for Potable Hot and Cold Water Distribution Supplies - Specification |
CED 50 |
|
69 |
IS 16087 : 2016 |
Biogas (Biomethane) - Specification (First Revision) |
PCD 3 |
|
70 |
IS/ISO 17292 : 2015 |
Metal ball valves for petroleum petrochemical and allied industries First Revision |
MED 17 |
|
71 |
IS 17875 : 2022 |
Stainless Steel seamless pipes and tubes for general service |
MTD 19 |
|
72 |
IS 17876 : 2022 |
Stainless steel welded pipes and tubes for general service |
MTD 19 |
|
73 |
IS/ISO 22109 : 2020 |
Industrial Valves - Gearbox for Valves |
MED 17 |
