| SNo |
IS Number |
Title |
Technical Committee |
| 1 |
IS 13882 : Part 1 : 1993 |
Optical fibre cables: Part 1 Generic specification |
LITD 11 |
| 2 |
IS/IEC 61757 : PART 1 : 1998 |
Fibre optic sensors: Part 1 generic specification |
LITD 11 |
| 3 |
IS 2102 : Part 2 : 1993 |
General tolerances: Part 2 geometrical tolerances for features without individual tolerance indications |
PGD 37 |
| 4 |
IS 13547 : Part 1 : 2010 |
Manipulating industrial robots -- Mechanical interfaces: Part 1 Plates (second revision) |
PGD 18 |
| 5 |
IS 13547 : PART 2 : 2010 |
Manipulating industrial robots -- Mechanical interfaces: Part 2 Shafts (first revision) |
PGD 18 |
| 6 |
IS 12160 : 2015 |
Geometrical product specifications (GPS) -- Fundamentals --Concepts, principles and rules (First Revision) |
PGD 24 |
| 7 |
IS 11670 : 1993 |
Technical drawings -- Abbreviations and symbols for use in technical drawings (First Revision) |
PGD 24 |
| 8 |
IS 13847 : 1993 |
Technical drawings - Tolerancing of orientation and location - Projected tolerance zone |
PGD 24 |
| 9 |
IS 14722 : 2016 |
Geometrical product specifications (GPS) -- Drawing indications for moulded parts in technical product documentation (TPD) (First Revision) |
PGD 24 |
| 10 |
IS 12937 : 1990 |
Engineering metrology - Methods of testing straightness, flatness and perpendicularity |
PGD 25 |
| 11 |
IS 2220 : 1990 |
Engineering metrology - Steel straightedges - Specification (First Revision) |
PGD 25 |
| 12 |
IS 2949 : 1992 |
Engineering metrology - Plain V - Blocks for inspection purposes - Specification (Second Revision) |
PGD 25 |
| 13 |
IS 2984 : 2003 |
Slip gauges - Specification [ISO title : geometrical product specifications (GPS) - length standards : gauge blocks] (Second Revision) |
PGD 25 |
| 14 |
IS 4563 : 1987 |
Specification for block squares (First Revision) |
PGD 25 |
| 15 |
IS 5268 : Part 1 : 1991 |
Engineering metrology - Straightedges: Part 1 cast iron straightedges (bow shaped or camel back type and 1-Section or parallel type) (First Revision) |
PGD 25 |
| 16 |
IS 5359 : 1987 |
Specification for sine bars (First Revision) |
PGD 25 |
| 17 |
IS 14150 : 2005 |
Hydraulic fluid power - Pressure relief valves - Mounting surfaces (First Revision) |
PGD 36 |
| 18 |
IS/IEC 60320 : Part 2 : Sec 2 : 1998 |
Appliance couplers for household and similar general purposes: Part 2: Sec 2 interconnection couplers for household and similar equipment |
ETD 14 |
| 19 |
IS 13090 : 2018 |
Automotive vehicles - Commercial vehicles - Clutch housings - Dimensions (First Revision) |
TED 2 |
| 20 |
IS 11644 : 1999 |
Tolerances of form and position for aerospace bolts and screws (First Revision) |
TED 14 |
| 21 |
IS/IEC 60876 : Part 1 : 2014 |
Fibre optic interconnecting devices and pass4e components - Fibre optic spatial switches: Part 1 generic specification (First Revision) |
LITD 11 |
| 22 |
IS 6197 : 2019 |
Test chart for vertical boring and turning mills with table diameter up to 1600 mm (First Revision) |
PGD 35 |
| 23 |
IS 15044 : 2019 |
Geometrical Product Specifications (GPS) -- Dimensioning and Tolerancing -- Non-rigid parts (First Revision) |
PGD 24 |
| 24 |
IS 16736 : 2020 |
Rolling Bearings — Needle Rollers — Boundary Dimensions, Geometrical Product Specifications ( GPS ) and Tolerance Values ( First Revision ) |
PGD 13 |
| 25 |
IS/IEC 60874 : Part 1 : 2011 |
Fibre Optic Interconnecting Devices and Passive Components — Connectors for Optical Fibres and Cables Part 1 Generic Specification |
LITD 11 |
| 26 |
IS 15045 : Part 1 : 2001 |
Pneumatic fluid power - Five port directional control valves: Part 1 mounting interface surfaces without electrical connector |
PGD 36 |
| 27 |
IS 15045 : Part 2 : 2001 |
Pneumatic fluid power - Five port directional control valves: Part 2 mounting interface surfaces with optional electrical connector |
PGD 36 |
| 28 |
IS 15480 : Part 1 : 2018 |
Fibre optic interconnecting devices and pass4e components - Fibre optic pass4e power control devices: Part 1 generic specification (First Revision) |
LITD 11 |
| 29 |
IS 15274 : 2003 |
Tolerances for fasteners - Plain washers for bolts, screws and nuts - Product grades a and c |
PGD 37 |
| 30 |
IS 17461 : 2021 |
VEGETABLE FATS AND OILS - ISOMERIC DIACYLGLYCEROLS - DETERMINATION OF RELATIVE AMOUNTS OF 1,2 AND 1,3-DIACYLGLYCEROLS (Adoption of ISO 29822 : 2009) |
FAD 13 |
| 31 |
IS 13998 : 2021 |
Multi-Point Diamond Impregnated Dressing Tools — Specification (First Revision of IS 13998 ) |
PGD 9 |
| 32 |
IS 8000 : Part 3 : 1992 |
Technical drawings - Geometrical tolerancing: Part 3 dimensioning and tolerancing of profiles (Second Revision) |
PGD 24 |
| 33 |
IS 10714 : Part 1 : 2006 |
Technical drawings - General principles of presentation: Part 1 introduction and index |
PGD 24 |
| 34 |
IS 12586 : 2021 |
Brazed low carbon steel gas cylinders not exceeding 13 litre water capacity Specification |
MED 16 |
| 35 |
IS 10721 : 1983 |
Datum and datum systems for, geometrical tolerancing on technical drawings (ISO Title : Technical Drawing -- Geometrical Tolerancing -- Datum and Datum -- Systems for Geometrical Tolerances) |
PGD 24 |
| 36 |
IS 15934 : Part 3 : 2022 |
LIQUID CRYSTAL DISPLAY DEVICES PART 3: LIQUID CRYSTAL DISPLAY LCD CELLS SECTIONAL SPECIFICATION |
LITD 4 |
| 37 |
IS 16561 : Part 6 : 2022 |
ERGONOMIC DESIGN OF CONTROL CENTRES — PART 6: ENVIRONMENTAL REQUIREMENTS FOR CONTROL ROOMS |
PGD 15 |
| 38 |
IS 13099 : 2001 |
Geometrical product specifications (GPS) -- Geometrical tolerancing -- Positional tolerancing (First Revision) |
PGD 24 |
| 39 |
IS 5692 : 2019 |
Rolling bearings -- Radial bearings -- Geometrical product specifications (GPS) and tolerance values (Second Revision) |
PGD 13 |
| 40 |
IS 5933 : 2019 |
Rolling bearings -- Thrust bearings -- Geometrical product specification (GPS) and tolerance values (Fourth Revision) |
PGD 13 |
| 41 |
IS/ISO 12297 : 2012 |
Rolling Bearings — Steel Cylindrical Rollers — Dimensions and Tolerances |
PGD 13 |
| 42 |
IS 16015 : 2022 |
Mortise locks and latches (Mechanically Operated) - Specification (first revision) |
MED 33 |
| 43 |
IS 15327 : 2022 |
Welding coordination - Tasks and responsibilities (Second Revision) |
MTD 11 |
| 44 |
IS 8000 : Part 2 : 2019 |
Geometrical product specifications (GPS) -- Geometrical tolerancing: Part 2 Maximum material requirement (MMR), least material requirement (LMR) and reciprocity requirement (RPR) (Second Revision) |
PGD 24 |
| 45 |
IS 16593 : Part 13 : 2022 |
Arc welding equipment Part 13: Welding current return clamp |
ETD 21 |
| 46 |
IS/ISO/IEC GUIDE 46 : 2017 |
Comparative Testing Of Consumer Products And Related Services - General Principles |
MSD 15 |
| 47 |
IS 9246 : 2022 |
Chapati Machine - Specification |
MED 33 |
| 48 |
IS 15533 : 2018 |
Cycles - Safety requirements for bicycles for young children (First Revision) |
TED 16 |
| 49 |
IS 18057 : Part 1 : 2023 |
Woodworking machines Safety Part 1: Common requirements |
PGD 35 |
| 50 |
IS 9316 : Part 8 : 2023 |
METHODS OF TEST FOR RUBBER LATEX PART 8 DETERMINATION OF TOTAL IRON ISO 1657:1986 IDT |
PCD 29 |
| 51 |
IS 9972 : 2023 |
Automatic Sprinkler Heads for Fire Protection Service - Specification (Second Revision) |
CED 22 |
