| SNo |
IS Number |
Title |
Technical Committee |
| 1 |
IS 14243 : Part 1 : 1995 |
Selection and development of site for building in hill areas - Guidelines: Part 1 Microzonation of urban centres |
CED 48 |
| 2 |
IS 14243 : Part 2 : 1995 |
Selection and development of site for building in hill areas - Guidelines: Part 2 Selection and development |
CED 48 |
| 3 |
IS/ISO 6194 : PART 1 : 2007 |
Rotary shaft lip - Type seals incorporating elastomeric sealing elements: Part 1 nominal dimensions and tolerances |
MED 30 |
| 4 |
IS 5129 : Part 2 : 2003 |
Rotary Shaft Radial Lip Type Seal - Part 2 : Vocabulary |
MED 30 |
| 5 |
IS 5129 : Part 3 : 2000 |
Rotary Shaft Lip Type Seals - Part 3 : Storage, Handling and Installation |
MED 30 |
| 6 |
IS 5129 : Part 5 : 2000 |
Rotary shaft lip type seals: Part 5 identification of visual imperfections |
MED 30 |
| 7 |
IS 15545 : Part 1 : 2015 |
Rotary shaft lip - Type seals incorporating thermoplastic sealing elements: Part 1 nominal dimensions and tolerances (First Revision) |
MED 30 |
| 8 |
IS 15545 : Part 3 : 2015 |
Rotary shaft lip - Type seals incorporating thermoplastic sealing elements: Part 3 storage, handling and installation (First Revision) |
MED 30 |
| 9 |
IS 15545 : Part 4 : 2004 |
Rotary shaft lip - Type seals incorporating thermoplastic sealing elements: Part 4 performance test procedures |
MED 30 |
| 10 |
IS 15545 : Part 5 : 2017 |
Rotary shaft lip - Type seals incorporating thermoplastic sealing elements: Part 5 identification of visual imperfections (First Revision) |
MED 30 |
| 11 |
IS 10143 : 1995 |
Pneumatic fluid power - Single rod cylinders, 1000 kPa (10 Bmar) series, with detachable mountings, bores from 32 mm to 320 mm - Mounting dimensions (First Revision) |
PGD 36 |
| 12 |
IS 10187 : 2013 |
Hydraulic fluid power - Four - Port directional control valves - Mounting surfaces (Second Revision) |
PGD 36 |
| 13 |
IS 10433 : Part 2 : 2002 |
Male stud tee body (Stud Run) for oil - Hydraulic couplings - Specification: Part 2 made from bar stock (First Revision) |
PGD 36 |
| 14 |
IS 11146 : 1999 |
Hydraulic fluid power - Cylinders - Bore and rod area ratios (First Revision) |
PGD 36 |
| 15 |
IS 11147 : 1984 |
Recommendations for parameter definitions and letter symbols for hydraulic fluid power pumps, motors and integral transmissions |
PGD 36 |
| 16 |
IS 11245 : 1999 |
Pneumatic cylinders purchase - Specification (First Revision) |
PGD 36 |
| 17 |
IS 11277 : 2004 |
Hydraulic fluid power - Gas - Loaded accumulators with separator - Ranges of pressures and volumes and characteristic quantities (First Revision) |
PGD 36 |
| 18 |
IS 11337 : 2002 |
Purchase Specification for hydraulic cylinders (First Revision) |
PGD 36 |
| 19 |
IS 11559 : 1995 |
Hydraulic fluid power - Cylinders - Rod end spherical eyes - Mounting dimensions (First Revision) |
PGD 36 |
| 20 |
IS 11560 : 1995 |
Hydraulic fluid power - Cylinders - Rod end plain eyes - Mounting dimensions (First Revision) |
PGD 36 |
| 21 |
IS 11845 : Part 1 : 1994 |
Fluid logic circuits for fluid power systems: Part 1 symbols for binary logic and related functions (First Revision) |
PGD 36 |
| 22 |
IS 11845 : Part 2 : 1995 |
Fluid Logic circuits for fluid - Power systems: Part 2 symbols for supply and exhausts as related to logic symbols (First Revision) |
PGD 36 |
| 23 |
IS 11845 : Part 3 : 1994 |
Fluid logic circuits for fluid power systems: Part 3 symbols for logic sequencers and related functions |
PGD 36 |
| 24 |
IS 12498 : 1988 |
Method of test for evaluation of performance of air pressure regulators |
PGD 36 |
| 25 |
IS 12593 : 2000 |
Hydraulic fluid power - Single rod cylinders, 16 mpa (160 Bar) compact series - Tolerances (First Revision) |
PGD 36 |
| 26 |
IS 12597 : 1988 |
Recommendation on units for fluid power system |
PGD 36 |
| 27 |
IS 12723 : 2020 |
Pneumatic Fluid Power - Single Rod Cylinders, 1 000 kPa (10 bar) series, bores from 8 mm to 25 mm - Basic and Mounting Dimensions ( First Revision ) |
PGD 36 |
| 28 |
IS 13085 : 1991 |
Hydraulic fluid power - Single rod cylinders, 160 bar (16 Mpa) medium series - Port dimensions |
PGD 36 |
| 29 |
IS 13102 : 1991 |
Hydraulic - Fluid power - Single rod cylinders, 250 bar (25 Mpa) series - Port dimensions |
PGD 36 |
| 30 |
IS 13103 : 2005 |
Hydraulic fluid power - Single rod cylinders, 16 mpa (160 Bar) compact series - Port dimensions (First Revision) |
PGD 36 |
| 31 |
IS 13434 : 2005 |
Hydraulic fluid power - Single rod cylinders, 16 mpa (160 Bar) medium and 25 mpa (250 Bar) series - Tolerances (First Revision) |
PGD 36 |
| 32 |
IS 13569 : 1993 |
Hydraulic fluid power - Fluid sample containers - Qualifying and controlling cleaning methods |
PGD 36 |
| 33 |
IS 13570 : 2000 |
HYDRAULIC FLUID POWER - PARTICULATE CONTAMINATION ANALYSIS - EXTRACTlON OF FLUID SAMPLES FROM LINES OF AN OPERATING SYSTEM (First Revision) |
PGD 36 |
| 34 |
IS 13614 : Part 2 : 1993 |
Hydraulic fluid power - Quick - Action couplings: Part 2 test methods |
PGD 36 |
| 35 |
IS 13617 : 1992 |
Evaluation of pressure drop versus flow characteristics of pneumatic filters - Method of test |
PGD 36 |
| 36 |
IS 13876 : Part 1 : 1993 |
Guide for marking system for fluid power components: Part 1 cylinders |
PGD 36 |
| 37 |
IS 13876 : Part 2 : 1993 |
Guide for marking system for fluid power components: Part 2 valves |
PGD 36 |
| 38 |
IS 13876 : Part 3 : 1993 |
Guide for marking system for fluid power components: Part 3 pumps and motors |
PGD 36 |
| 39 |
IS 14150 : 2005 |
Hydraulic fluid power - Pressure relief valves - Mounting surfaces (First Revision) |
PGD 36 |
| 40 |
IS 14601 : 1998 |
Method for presenting performance data for hydraulic pumps |
PGD 36 |
| 41 |
IS 14602 : 1999 |
Installation methods of positive displacement hydraulic pumps and motors - Guidelines |
PGD 36 |
| 42 |
IS 14740 : 1999 |
Pneumatic fluid power - Components using compressible fluids - Determination of flow - Rate characteristics |
PGD 36 |
| 43 |
IS 14848 : 2000 |
Hydraulic fluid power - Pumps and motors - Geometric displacements |
PGD 36 |
| 44 |
IS 14849 : Part 2 : 2018 |
Hydraulic fluid power - Determination of characteristics of motors: Part 2 startability (First Revision) |
PGD 36 |
| 45 |
IS 14875 : 2000 |
Compressed air filters - Evaluation parameters |
PGD 36 |
| 46 |
IS 15045 : Part 3 : 2001 |
Pneumatic fluid power - Five port directional control valves: Part 3 code system for communication of valve functions |
PGD 36 |
| 47 |
IS 15097 : 2002 |
Pneumatic fluid power - Cylindrical quick - Action couplings for maximum working pressures of 10 bar, 16 bar and 25 bar (1 Mpa, 1.6 Mpa And 2.5 Mpa) - Plug connecting dimensions, Specifications, application guidelines and testing |
PGD 36 |
| 48 |
IS 15276 : 2002 |
Metallic tube connections for fluid power and general use 24° cone connectors with o - Ring weld - On nipples |
PGD 36 |
| 49 |
IS 15277 : 2002 |
Metallic tube connections for fluid power and general use test methods for threaded hydraulic fluid power connections |
PGD 36 |
| 50 |
IS 15331 : 2003 |
Pneumatic fluid power - Identification of ports and control mechanisms of control valves and other components |
PGD 36 |
| 51 |
IS 15577 : Part 3 : 2005 |
Connections for general use and fluid power - Ports and stud ends with ISO 261 threads with elastomeric or Metal - to - Metal sealing: Part 3 stud ends with metal - To - Metal sealing (Type B) |
PGD 36 |
| 52 |
IS 5107 : 2004 |
Fluid power systems and components - Nominal pressures (First Revision) |
PGD 36 |
| 53 |
IS 8384 : 2013 |
Hydraulic fluid power - Filter elements - Verification of collapse/burst pressure rating (First Revision) |
PGD 36 |
| 54 |
IS 8385 : 2005 |
Hydraulic fluid power - Filter elements - Verification of material compatibility with fluids (First Revision) |
PGD 36 |
| 55 |
IS 8526 : 1994 |
Sizes for bores and port threads for pneumatic fluid power cylinders - Recommendations (First Revision) |
PGD 36 |
| 56 |
IS 8532 : 2013 |
Hydraulic fluid power - Filter elements - Determination of resistance to flow fatigue using particulate contaminant (Second Revision) |
PGD 36 |
| 57 |
IS 8805 : 2002 |
General requirements for ferrule type couplings used in oil hydraulic systems (First Revision) |
PGD 36 |
| 58 |
IS/ISO 3939 : 1977 |
Fluid power systems and components - Multiple lip packing sets - Methods for measuring stack heights |
PGD 36 |
| 59 |
IS/ISO 4412 : PART 1 : 1991 |
Hydraulic fluid power - Test code for determination ok airborne noise levels: Part 1 pumps |
PGD 36 |
| 60 |
IS/ISO 4412 : PART 2 : 1991 |
Hydraulic fluid power - Test code for determination of airborne noise levels: Part 2 motors |
PGD 36 |
| 61 |
IS/ISO 6547 : 1981 |
Hydraulic fluid power - Cylinders - Piston seal housings incorporating bearing rings - Dimensions and tolerances |
PGD 36 |
| 62 |
IS/ISO 7425 : PART 2 : 1989 |
Hydraulic fluid power - Housings for elastomer - Energized, plastic - Faced seals - Dimensions and tolerances: Part 2 rod seal housings |
PGD 36 |
| 63 |
IS 11003 : Part 1 : 2017 |
Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 mpa (160 Bar) series: Part 1 medium series (Second Revision) |
PGD 36 |
| 64 |
IS 15170 : 2017 |
Hydraulic fluid power - Component cleanliness - Guidelines for achieving and controlling cleanliness of components from manufacturer to installation (First Revision) |
PGD 36 |
| 65 |
IS 13535 : 2017 |
Hydraulic fluid power - Filters - Filter multi - Pass method for evaluating filtration performance of filter element (Second Revision) |
PGD 36 |
| 66 |
IS 14849 : Part 1 : 2017 |
Hydraulic fluid power - Determination of characteristics of motors: Part 1 at constant low speed and at constant pressure (First Revision) |
PGD 36 |
| 67 |
IS 7513 : Part 2 : 2019 |
Fluid power systems and components ? graphical symbols and circuit diagrams: Part 2 circuit diagrams (First Revision) |
PGD 36 |
| 68 |
IS 7513 : Part 2 : 2019 |
Fluid power systems and components ? graphical symbols and circuit diagrams: Part 2 circuit diagrams (First Revision) |
PGD 36 |
| 69 |
IS 13251 : 2019 |
Hydraulic fluid power ? mounting dimensions for accessories for single rod cylinders, 16 mpa (160 Bar) medium and 25 mpa (250 Bar) series (First Revision) |
PGD 36 |
| 70 |
IS 14167 : 2019 |
Pneumatic fluid power ? cylinders ? final examination and acceptance criteria (First Revision) |
PGD 36 |
| 71 |
IS 17083 : Part 9 : 2019 |
Graphical symbols for diagrams: Part 9 Pumps, compressors and fans |
PGD 24 |
| 72 |
IS 17083 : Part 10 : 2019 |
Graphical symbols for diagrams: Part 10 Fluid power converters |
PGD 24 |
| 73 |
IS 17159 : 2019 |
Hydraulic fluid power - Hoses and hose assemblies - Test methods |
PCD 29 |
| 74 |
IS 7513 : Part 1 : 2019 |
Fluid Power Systems and Components ― Graphical Symbols and Circuit Diagrams Part 1 Graphical Symbols for Conventional Use and Data-Processing Applications ( First Revision ) |
PGD 36 |
| 75 |
IS 15179 : 2002 |
Hydraulic fluid power - Compatibility between elastomeric materials and fluids |
PGD 36 |
| 76 |
IS 15179 : 2002 |
Hydraulic fluid power - Compatibility between elastomeric materials and fluids |
PGD 36 |
| 77 |
IS 11003 : Part 2 : 2020 |
Hydraulic Fluid Power — Mounting Dimensions for Single Rod Cylinders, 16 MPa ( 160 bar ) Series Part 2 Compact Series ( Second Revision ) |
PGD 36 |
| 78 |
IS 10481 : 2020 |
Hydraulic Fluid Power — General Rules and Safety Requirements for Systems and their Components ( Second Revision ) |
PGD 36 |
| 79 |
IS 13571 : 2020 |
Hydraulic Fluid Power — Calibration of Automatic Particle Counters for Liquids ( First Revision ) |
PGD 36 |
| 80 |
IS 14876 : 2020 |
Pneumatic Fluid Power ? Compressed-air lubricators Part 1 Main Characteristics to be Included in Supplier’s Literature and Product-marking Requirements ( First Revision ) |
PGD 36 |
| 81 |
IS 8208 : 2020 |
Fluid Power Systems and Components — Cylinder Bores and Piston Rod Diameters and Area Ratios — Metric Series ( Second Revision ) |
PGD 36 |
| 82 |
IS 10411 : 2020 |
Fluid Power Systems and Components — Cylinders — Basic Series of Piston Strokes ( First Revision ) |
PGD 36 |
| 83 |
IS 10983 : 1994 |
Fluid power - Cylinders - Housing for piston and rod seals in reciprocating applications - Dimensions and tolerances - Recommendations (First Revision) |
PGD 36 |
| 84 |
IS 12092 : 1987 |
Method of test for hose assemblies used in hydraulic fluid power systems |
PGD 36 |
| 85 |
IS 12725 : 2002 |
Pneumatic fluid power - General rules relating to systems (First Revision) |
PGD 36 |
| 86 |
IS 13086 : 1999 |
Pneumatic fluid power - Cylinders, 1000 kPa (10 Bar) series - Rod end spherical eyes - Mounting dimensions (First Revision) |
PGD 36 |
| 87 |
IS 13087 : 1999 |
Pneumatic fluid power - Cylinders, 1000 kPa (10 Bar) series - Rod end clevis - Mounting dimensions (First Revision) |
PGD 36 |
| 88 |
IS 13170 : Part 1 : 1999 |
Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O - Ring sealing: Part 1 ports with O - Ring seal in truncated housing (First Revision) |
PGD 36 |
| 89 |
IS 13170 : Part 2 : 1999 |
Connections for fluid power and general use - Ports and stud ends with ISO 261 threads and O - Ring sealing: Part 2 heavy duty (S Series) stud ends - Dimensions, design, test methods and requirements |
PGD 36 |
| 90 |
IS 13170 : Part 3 : 1999 |
Connections for fluid power and general use - Ports and stud ends withISO 261 threads and o - Ring sealing: Part 3 light duty (L Series) stud ends - Dimensions, design,test methods and requirements |
PGD 36 |
| 91 |
IS 14148 : 2005 |
Hydraulic fluid power - Pressure - Reducing valves, sequence valves, unloading valves, throttle valves and check valves - Mounting surfaces (First Revision) |
PGD 36 |
| 92 |
IS 14423 : 1997 |
Luid power systems and components - Connectors and associated components - Nominal pressures |
PGD 36 |
| 93 |
IS 13095 : 1991 |
Butterfly Valves for General Purposes ( First Revision ) |
MED 17 |
| 94 |
IS 15834 : 2008 |
Stainless Steel Sliding Door Bolts ( Aldrops ) for Use With Padlocks - Specification ( First Revision ) |
CED 15 |
| 95 |
IS 15045 : Part 1 : 2001 |
Pneumatic fluid power - Five port directional control valves: Part 1 mounting interface surfaces without electrical connector |
PGD 36 |
| 96 |
IS 15045 : Part 2 : 2001 |
Pneumatic fluid power - Five port directional control valves: Part 2 mounting interface surfaces with optional electrical connector |
PGD 36 |
| 97 |
IS 15178 : 2002 |
Hydraulic fluid power - Fire - Resistant (Fr) fluids - Guidelines for use |
PGD 36 |
| 98 |
IS 13614 : Part 1 : 1995 |
Hydraulic fluid power - Quick action couplings: Part 1 dimensions and requirements |
PGD 36 |
| 99 |
IS 15545 : Part 2 : 2004 |
Rotary shaft lip - Type seals incorporating thermoplastic sealing elements: Part 2 vocabulary |
MED 30 |
| 100 |
IS 15168 : 2002 |
Fluid power systems and components - Cylinders - Identification code for mounting dimensions and mounting types |
PGD 36 |
| 101 |
IS 9269 : 2019 |
Hydraulic fluid power ? filters ? evaluation of differential pressure versus flow characteristics (Second Revision) |
PGD 36 |
| 102 |
IS 10585 : 2019 |
Hydraulic fluid power ? cylinders ? acceptance tests (Second Revision) |
PGD 36 |
| 103 |
IS 13534 : 2013 |
Hydraulic fluid power - Valves - Determination of pressure differential/ flow characteristics (First Revision) |
PGD 36 |
| 104 |
IS 17091 : 2019 |
Pneumatic fluid power ? push - In connectors for thermoplastic tubes |
PGD 36 |
| 105 |
IS 8383 : 2017 |
Hydraulic fluid power - Filter elements - Verification of fabrication integrity and determination of the first bubble point (Second Revision) |
PGD 36 |
| 106 |
IS 10069 : 2017 |
Hydraulic fluid power - Positive displacement pumps, motors and integral transmission - Methods of testing and presenting basic steady state performance (Second Revision) |
PGD 36 |
| 107 |
IS 15181 : Part 1 : 2002 |
Hydraulic fluid power - Measurement techniques: Part 1 general measurement principles |
PGD 36 |
| 108 |
IS 15181 : Part 2 : 2002 |
Hydraulic fluid power - Measurement techniques: Part 2 measurement of average steady - State pressure in a closed conduit |
PGD 36 |
| 109 |
IS/ISO 7425 : PART 1 : 1988 |
Hydraulic fluid power - Housings for elastomer - Energized, piastic - Faced seals - Dimensions and tolerances: Part 1 piston seal housings |
PGD 36 |
