SNo |
IS Number |
Title |
Technical Committee |
1 |
IS 319 : 2007 |
Free cutting brass bars, rods and section - Specification (Fifth Revision) |
MTD 8 |
2 |
IS 554 : 1999 |
Pipe threads where pressure - Tight joints are made on the threads - Dimensions, tolerances and designation (Fourth Revision) |
PGD 37 |
3 |
IS 617 : 1994 |
Cast aluminium and its alloys - Ingots and castings for general engineering purposes - Specification (Third Revision) |
MTD 7 |
4 |
IS 742 : 1981 |
Specification for zinc base alloy die castings (Second Revision) |
MTD 9 |
5 |
IS 2305 : 1988 |
Method for mercurous nitrate test for copper and copper alloys (First Revision) |
MTD 8 |
6 |
IS 2643 : 2005 |
Pipe threads where pressure - Tight joints are not made on the threads - Dimensions, tolerances and designation (Third Revision) |
PGD 37 |
7 |
IS 3224 : 2002 |
Valve fittings for compressed gas cylinders excluding liquefied petroleum gas (LPG) cylinders - Specification (Third Revision) |
MED 16 |
8 |
IS 3400 : Part 2 : 2014 |
Methods of test for vulcanized rubber: Part 2 rubber, vulcanized or thermoplastic - Determination of hardness (Hardness Between 10 Irhd And 100 Irhd) (Fourth Revision) |
PCD 29 |
9 |
IS 3400 : Part 4 : 2012 |
Methods of test for vulcanized rubber: Part 4 accelerated ageing and heat resistance (Third Revision) |
PCD 29 |
10 |
IS 3400 : Part 10 : 1977 |
Methods of test for vulcanized rubbers: Part x compression set at constant strain (First Revision) |
PCD 29 |
11 |
IS 3624 : 1987 |
Specification for pressure and vacuum gauges (Second Revision) |
ETD 18 |
12 |
IS 4218 : Part 1 : 2001 |
ISO general purpose metric screw threads: Part 1 basic profile - second revision) |
PGD 37 |
13 |
IS 4218 : Part 3 : 1999 |
ISO general purpose metric screw threads: Part 3 basic dimensions (Second Revision) |
PGD 37 |
14 |
IS 4218 : Part 4 : 2001 |
ISO general purpose metric screw threads: Part 4 selected sizes for screws, bolts and nuts (Second Revision) |
PGD 37 |
15 |
IS 5116 : 2020 |
Domestic and Commercial Equipment for Use with LPG — General Requirements ( Fourth Revision ) |
MED 23 |
16 |
IS 6009 : 1970 |
Method for evaluation of results of accelerated corrosion test |
MTD 24 |
17 |
IS 6912 : 2005 |
Copper and copper alloys forging stock and forging - Specification (Second Revision) |
MTD 8 |
18 |
IS 8737 : 2017 |
Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision) |
MED 16 |
19 |
IS 9798 : 2013 |
Low pressure regulators for use with liquefied petroleum gas (LPG) - Specification (Second Revision) |
MED 16 |
20 |
IS 9844 : 1981 |
Methods of testing corrosion resistance of electroplated and anodized aluminium coatings by neutral salt spray test |
MTD 24 |